Warning – Brinkmann Series 6419 User Manual

Page 8

WARNING

••

err u

e y

urr g

grriillll w

wiitth

utt lle

k tte

sttiin

g a

allll g

s c

cttiio

s a

d h

s.. S

e tth

e s

cttiio

n o

k T

sttiin

" iin

n tth

hiis

s m

all ffo

orr p

prro

err p

prro

urre

s..

e p

prre

urre

e rre

ulla

atto

orr a

d h

e a

blly

y s

plliie

d w

wiitth

h y

urr g

s g

grriillll m

stt b

e u

d..

••

O N

T a

atttte

ptt tto

o c

ctt iitt tto

o a

y o

otth

err ffu

ell s

plly

y s

urrc

e s

h a

s a

a n

attu

urra

all g

s lliin

e..

••

O N

T u

e a

y o

otth

err p

prre

urre

e rre

ulla

atto

orr//h

e a

blly

y o

otth

err tth

n tth

e o

e s

plliie

d w

wiitth

h y

urr g

grriillll..

plla

ntt p

prre

urre

e rre

ulla

atto

orr//h

e a

blly

y m

stt b

e p

arrtt N

o 1

5--6

9--2

2,, w

hiic

h c

n b

e o

btta

aiin

y c

ntta

cttiin

g c

stto

err s

errv

viic

e a

att 8

0--5

7--0

7..

••

O N

T a

atttte

ptt tto

o a

djju

stt o

orr rre

aiirr tth

e rre

ulla

atto

orr.. T

e rre

ulla

atto

orr iis

s d

siig

d tto

o o

erra

atte

e a

att a

xiim

m o

uttp

utt p

prre

urre

e o

off 1

1 iin

s o

off w

atte

err c

ollu

n ((2

2..7

4 k

a))..

During assembly and/or replacement of the gas cylinder, keep the gas supply hose free of kinks and/or
damage.

Visually inspect the hose assembly prior to each use for evidence of damage, excess wear, or
deterioration. If found, replace the assembly before using your grill. Only the manufacturer's supplied
replacement should be used.

TIIN

G H

E A

D R

R T

O A

N L

P G

S C

LIIN

••

urre

e tth

e tta

k v

allv

e iis

s CLOSED p

prriio

orr tto

o c

cttiin

g tth

e L

P g

s c

ylliin

err tto

o y

urr g

grriillll.. T

urrn

n tth

allv

e k

b c

cllo

wiis

e tto

o p

prro

errlly

y c

cllo

e tth

e v

allv

e.. R

d a

d ffo

ollllo

w a

allll iin

sttrru

cttiio

s a

d w

arrn

niin

n tth

e s

plly

y h

e s

affe

etty

y tta

s.. R

d a

d ffo

ollllo

w a

allll w

arrn

niin

s iin

n tth

hiis

s m

all c

errn

niin

g tth

e s

affe

e o

off L

P g

s c

ylliin

errs

s a

d tth

e h

e a

d rre

ulla

atto

orr b

effo

orre

e c

cttiin

g c

ylliin

err tto

o g

grriillll.. R

d ffo

ollllo

w a

allll w

arrn

niin

s o

n tth

e L

P c

ylliin

err..

TIIN

G H

E A

D R

1. Check that the cylinder valve is closed by turning the knob clockwise.

2. Check that the grill’s burner control knobs are in the "OFF" positions.

3. Remove the protective plastic cap from the cylinder valve and the connection device.

4. Hold regulator and insert the nipple of connection device into the LP cylinder valve outlet. Ensure that

the device is centered properly.

5. Turn the large coupling nut clockwise by hand and tighten to a full stop. Take care not to cross thread

the coupling nut onto the cylinder valve. Do not over-tighten the knob onto the valve. Do not use tools
to tighten connection.

Note:

If you are unable to make the connection, repeat Steps 4 and 5.

6. Check that the hose does not contain kinks, does not contact sharp edges, and does not contact

surfaces that may become hot during use.

7. Leak check all fittings before lighting your grill. See section on "Leak Testing" in this manual.

WARNING