Bryant SERIES E A10252 User Manual
Page 12
12
GUIDE SPECIFICATIONS
Gas Furnace
310AAV/JAV
General
SYSTEM DESCRIPTION
Furnish a _________________ fixed capacity gas-fired
furnace for use with natural gas or propane (factory
authorized conversion kit required for propane); furnish
cold air return plenum.
QUALITY ASSURANCE
Unit will be designed, tested and constructed to the
current ANSI Z 21.47/CSA 2.3 design standard for
gas-fired central furnaces.
Unit will be 3rd party certified by CSA to the current
ANSI Z 21.47/CSA 2.3 design standard for gas-fired
central furnaces.
Unit will carry the CSA Blue StarR label.
Unit efficiency testing will be performed per the current
DOE test procedure as listed in the Federal Register.
Unit will be certified for capacity and efficiency and
listed in the latest AHRI Consumer’s Directory of
Certified Efficiency Ratings.
Unit shall carry the current Federal Trade Commission
Energy Guide efficiency label.
DELIVERY, STORAGE AND HANDLING
Unit shall be shipped as single package only and is
stored
and
handled
per
unit
manufacturer’s
recommendations.
WARRANTY (for inclusion by specifying engineer)
U.S. and Canada only. Warranty certificate available
upon request.
Products
EQUIPMENT
Components shall include: slow-opening gas valve to
reduce ignition noise, regulate gas flow, with electric
switch gas shut-off; flame proving sensor, hot surface
igniter, pressure switch assembly, flame rollout switch,
blower and inducer assembly, 40va transformer;
low--voltage (heating) (heating/cooling) thermostat.
Blower Wheel and Blower Motor
Galvanized blower wheel shall be centrifugal type,
statically and dynamically balanced. Blower motor of PSC
type shall be permanently lubricated with sealed bearings,
of _______hp, and shall be multiple-speed direct drive.
Blower motor shall be soft mounted to the blower scroll to
reduce vibration transmission.
Filters
Furnace may have reusable-type filters. Filter shall be
_______ in (x) _______in. (mm).
Casing
Casing shall be of .030 in. (.76 mm) thickness
minimum, pre--painted galvanized steel.
Inducer Motor
Inducer motor shall be soft mounted to reduce vibration
transmission.
Draft Safeguard Switch
Draft Safeguard Switch (blocked vent safeguard) shall
be factory installed to reduce the possibility of vent gas
infiltration due to a blocked or restricted vent pipe.
Heat Exchangers
Heat exchangers shall be a 4-Pass 20 gage aluminized
steel of fold-and-crimp sectional design when applied
operating under negative pressure.
Controls
Control shall include a micro-processor non--volatile
memory based integrated electronic control board with at
least 11 service troubleshooting codes displayed via
enhanced flashing LED diagnostic light on the control, a
self-test feature that checks all major functions of the
furnace
within
one
minute,
and
a
replaceable
automotive-type
circuit
protection
fuse.
Multiple
operational settings available including, separate blower
speeds for heating, cooling, and continuous fan.
Continuous fan speed may be adjusted from the
thermostat. Cooling airflow will be selectable between 350
or 400 CFM per ton of air conditioning.
OPERATING CHARACTERISTICS
Heating Capacity shall be ________ Btuh input;
________ Btuh output capacity.
Fuel Gas Efficiency shall be 80% AFUE.
Air delivery shall be ___________ CFM minimum at
0.50 In. W.C. external static pressure.
Dimensions shall be: depth __________ in. (mm);
width _________ in. (mm); height_________in. (mm)
(casing only). Height shall be_________in. (mm) with
A/C coil and _____________in. (mm) overall with
plenum.
ELECTRICAL REQUIREMENTS
Electrical supply shall be 115 volts, 60 Hz,
single--phase (nominal). Minimum wire size shall
be_________AWG; maximum fuse size or circuit breaker
shall be __________Amps.
SPECIAL FEATURES
Refer to section of the product data sheet identifying
accessories and descriptions for specific features and
available enhancements.
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
E
2010 Bryant Heating & Cooling Systems D 7310 W. Morris St. D Indianapolis, IN 46231
Printed in U.S.A.
Edition Date: 09/10
Replaces: PDS 310A.45.5
Catalog No. PDS310A.45.6
310AA
V
/J
A
V