Toshiba DV734 - Manual (Page 77)

77
PC connection
As PCs are sometimes supplied with a “conventional” CRT monitor, you may need to adjust the display settings of your PC’s
graphic card; otherwise the pictures may not appear correctly. Switch on your PC (still with your original monitor), select “1360 x
768” for the screen resolution, and select “60 Hz” for the on-screen refresh rate. Switch off your PC, and then connect it to your
TV while both items are switched off.
Monitor display modes
(according to graphic card)
Mode Resolution V. Frequency H. Frequency Pixel Clock Frequency
VGA 640 x 480 59.940 Hz 31.469 kHz 25.175 MHz
SVGA 800 x 600 60.317 Hz 37.879 kHz 40.000 MHz
XGA 1024 x 768 60.004 Hz 48.363 kHz 65.000 MHz
WXGA 1280 x 720 60.000 Hz 45.000 kHz 74.250 MHz
WXGA 1280 x 768 59.870 Hz 47.776 kHz 79.500 MHz
WXGA 1360 x 768 60.015 Hz 47.712 kHz 85.500 MHz
Select PC input
(1) Switch on the TV.
(2) Switch on the computer.
(3) Select the PC input mode on the TV
(see page 21). (When you use an
HDMI cable, select HDMI input
mode.)
Note:
• The PC audio input terminal on the TV
is shared with the HDMI 1 analogue
audio input terminal.
• If there is no video signal from the
computer when the TV is in PC mode,
No Signal will appear on the TV
screen.
• If a digital PC connection does show
a picture, proper working is not
guaranteed. Digital PC connection
is not granted for this TV.
Use a PC-VGA cable (not supplied) to connect the TV to your PC. You can also use
an HDMI cable to connect the TV to your PC. When the HDMI cable is used, the
audio cable is no longer required. If you use the HDMI-to-DVI cable, please connect
audio cable in the same way as VGA cable. Connect cables carefully. Do not bend
or break the connector pins.
To adjust the contrast:
1 During PC mode, press MENU SETUP to display the Main Menu screen.
2 Press to select Picture, and then press ENTER/CH LIST .
Press to select Picture Setting, and then press ENTER/CH LIST .
Select Contrast and then press ENTER/CH LIST .
Press to adjust the contrast.
3
Press EXIT/CANCEL to return to the normal screen.
After connecting a PC to your TV, you can now configure the display and audio settings.
To configure the display settings:
(1) Press MENU SETUP to display the Main Menu
screen.
(2) Press to select the Picture menu, and then press
ENTER/CH LIST .
(3) On the Picture menu, you can adjust various picture
properties such as brightness, contrast, sharpness,
colour, tint, colour temperature, backlight, and dynalight.
Note: Tint can be adjusted only when NTSC signal is
supported.
(4) For a list of available menu options in the Picture menu,
see page 32.
To configure the audio settings:
(1) Press MENU SETUP to display the Main Menu
screen.
(2) Press to select the Sound menu, and then press
ENTER/CH LIST .
(3) On the Sound menu, you can adjust the NICAM stereo
reception, and the bass, treble, balance, and sound
effects.
Note: NICAM is available only when the TV is set to ATV
mode.
(4) For a list of available menu options in the Sound menu,
see page 32.
TV （Back side view）
To PC/HDMI 1
AUDIO input
Audio cable
To HDMI input
VGA cable
HDMI-to-DVI cable To DVI output
PC
TUNER
HDMI 1 Y Pb Pr L R L R VIDEO
PC MONITOR
HEAD PHONE
PC/ HDMI 1
AUDIO
DIGITAL AUDIO
OPTICAL IN
IN
IN
OUT SCART (AV1)
COMPONENT COMPOSITE(AV2)
(All illustrated cables are not supplied.)
/
/
/
/ /