Pioneer VSX-D710S - Manual (Page 23)

23
En
Displays & Controls
Display
1 SIGNAL SELECT indicators
Light to indicate the type of input signal assigned for
the current component (see “Front Panel“, 0
SIGNAL SELECT). When the AUTO setting is being
used on VSX-D810S & VSX-D850S receivers a set of
brackets will appear around the SIGNAL SELECT
indicators.
2DIGITAL : Lights when a DOLBY DIGITAL
signal is played.
DTS : Lights when a source with DTS audio signals is
played.
ANALOG : Lights when an analog signal is selected.
DIGITAL : Lights when a digital audio signal is selected.
[ ]: Lights when the AUTO setting is selected. (VSX-
D810S/D850S only)
2 DTS indicator
Lights when DTS mode is being used.
3 2 DIGITAL indicator
When the 2 (DOLBY)/DTS mode of the receiver is
on, this lights to indicate playback of a Dolby Digital
signal. However, 2 PRO LOGIC lights during 2
channel playback of Dolby Digital.
4 2 PRO LOGIC indicator
When the 2 (DOLBY)/DTS mode of the receiver is
on, this lights to indicate playback of a Dolby Pro
Logic source.
5 DSP indicator
Lights when any Advanced Theater or DSP mode is
selected.
6 Surround Back indicator (VSX-D810S/D850S only)
Lights when most Surround Back channel flag encoded
(6.1channel) software is playing. (With some Surround
Back channel software the surround back indicator
won’t light because there is no flag encoded in the
software.) If you play DTS 5.1/6.1 channel software
surround sound will be heard whether it is encoded
with a surround back channel flag or not.
7 OVERLOAD indicator
This lights when an analog signal is too strong (the
SIGNAL SELECT needs to be on ANALOG). It
indicates the sound is distorting and the input signal
should be reduced.
8 ATT indicator
Lights when ATT is used to attenuate (reduce) the
level of the input signal (can only be used in
ANALOG mode).
1 2 3 4 8 7 9 0 = 5 6 -
~ @ !
SIGNAL SELECT
MIDNIGHT
LOUDNESS
DIRECT MONITOR
TUNED
MONO ANALOG DIGITAL
SP AB DIGITAL DTS
DIGITAL
PRO LOGIC
SB ATT
DSP
DNR
STEREO
dB
9 DIRECT indicator
Lights when source DIRECT is in use. This function
bypasses all tone, channel levels, DSP and Dolby
Surround effects.
MIDNIGHT indicator
Lights when MIDNIGHT listening mode is in use.
LOUDNESS indicator
Lights when the LOUDNESS is on. LOUDNESS is
used to boost the bass and treble when listening at
low levels.
0 SPEAKER indicator
Shows if the speaker system is on or not. SP
3A
(and/or) B means speakers are switched on. SP
3
means speakers are switched off.
- MONITOR indicator
Lights when MONITOR is selected to hear a
recording as it's being made (see page 34).
= TUNER indicators
MONO :
Lights when the mono mode is set using the
MPX MODE button.
TUNED :
Lights when a broadcast is being received.
STEREO :
Lights when a stereo FM broadcast is being received
in auto stereo mode.
~ MASTER VOLUME LEVEL
Shows the overall volume level. Volume level is
maintained even when the power is off.
---dB
indicates the minimum level, and 0dB indicates the
maximum level.
• Depending on the level settings you make for
individual channels, the MAX level can range
between –10dB and 0dB.
! DNR indicator (VSX-D810S/D850S only)
Lights when the digital noise reduction is on. Use to
reduce extraneous noise. It can be used with any
sound mode.
@ CHARACTER display
Shows the radio frequency or function (DVD/LD,
CD, etc.) receiver is using.