Pioneer SPX-HUD01 - Manual (Page 3)

Black plate (3,1)
These symbols on the products, packaging,
and/or accompanying documents mean that
used electrical and electronic products and
batteries should not be mixed with general
household waste.
For proper treatment, recovery and recy-
cling of old products and used batteries,
please take them to applicable collection
points in accordance with your national
legislation.
By disposing of these products and batteries
correctly, you will help to save valuable resour-
ces and prevent any potential negative effects
on human health and the environment which
could otherwise arise from inappropriate waste
handling.
For more information about collection and recy-
cling of old products and batteries, please con-
tact your local municipality, your waste disposal
service or the point of sale where you purchased
the items.
These symbols are only valid in the Euro-
pean Union.
For countries outside the
European Union:
If you wish to discard these items, please con-
tact your local authorities or dealer and ask for
the correct method of disposal.
Connection and installation
WARNING
! Use this unit with a 12-volt battery and nega-
tive earthing only.
Do not use the unit for a 24-volt vehicle.
There is a risk of a fire or malfunction.
! Never install the unit and wire the cables to
places where it will impair the performance
of an airbag.
When installing the unit to a vehicle
equipped with airbags, ask the vehicle manu-
facturer for precautions for the installation
work. There is a risk of incorrect deployment
of airbags, resulting in a fatal accident.
! Never install the unit to places where it will
obstruct the driver ’s vision, interfere with
driving, or cause danger to the passengers.
There is a risk of a traffic accident and injury.
! Never cut the insulation of the power cable
of this unit to share the power with other de-
vices.
Exceeding the current capacity of the power
cable may result in a fire, electric shock, or
malfunction.
! Never use the bolts and nuts of safety related
parts such as the steering, brake systems
and tank.
Using these may cause a brake failure, fire,
or traffic accident.
! Do not install the unit to a sun visor whose
shape is not supported by the unit.
Installing the unit to a sun visor whose
shape is not supported by the unit may
cause an accident or malfunction.
! Do not install the unit to a defective sun
visor.
Check if there are no defects on the sun visor
before installation. Installation to a defective
sun visor may cause the unit to fall, resulting
in an accident or malfunction.
! Do not leave the unit in a place subject to di-
rect sunlight.
Do not remove the combiner protection
sheet before the installation is completed.
The combiner may concentrate light into an
intense beam, causing smoke or fire.
! For your safety, ask your dealer to install the
unit and wire the cables, or change the in-
stallation location.
Installation, wiring, and disinstallation of the
unit require special skills and experience. In-
correct installation, wiring, or disinstallation
of the unit may cause serious damage to the
vehicle.
! Do not work in a place subject to direct sun-
light.
Doing so may cause a burn injury or blind-
ness.
! Disconnect the negative terminal of the bat-
tery before installation.
Short circuiting the positive and negative ter-
minals may cause electric shock or injury.
! Check the location of the pipes, tank, electri-
cal wiring, etc. before installation.
When installing the unit by drilling a hole in
the vehicle body, be careful not to interfere
with or contact the pipes, tank, electrical wir-
ing, etc. Furthermore, protect the processed
parts from rusting or the penetration of
water.
! Use the supplied parts and secure them
firmly.
Use of parts other than the supplied ones
may cause damage to other parts in the unit
or may not be able to firmly secure the unit.
If the unit comes loose, it may interfere with
driving, causing an accident and injury.
! Install the supplied parts as specified.
If the supplied parts are not installed as
specified, the parts may come loose and
drop off, resulting in an accident or malfunc-
tion.
! Use the supplied cables and connect them
securely.
Use the supplied cables and connect them
as specified. Use of cables other than the
supplied ones may cause a fire or malfunc-
tion.
! Follow the instructions in this manual to con-
nect and install the unit.
Failure to follow the instructions in this man-
ual to connect and install the unit may cause
a fire or accident.
! Secure the unit to sun visor with a fall pre-
vention belt.
Failure to do so may cause the unit to fall,
causing an accident and injury.
! Insulate an uninsulated part of the cable
with tape, etc.
A short-circuit may cause a fire, electric
shock, or malfunction.
! Wire the cables so that they do not get
caught on the vehicle body, screws, or mov-
ing parts such as a seat rail.
A disconnection or short-circuit may cause a
fire, electric shock, or malfunction.
! Wire and secure the cables so that they do
not interfere with driving.
Failure to do so may cause the cables to get
tangled around the steering wheel, gear
stick, brake pedal, etc., causing an accident.
! When you are finished with the installation
and wiring, check that the electric equip-
ment works normally as it did before instal-
ling the unit.
Using the unit whilst other electric equip-
ment does not work normally may cause a
fire, electric shock, or traffic accident.
! Store small parts such as screws out of the
reach of small children.
Should the parts be swallowed, consult a
doctor immediately.
CAUTION
! Never cut a cable part way along it.
If a fuse is connected to the cable, the pro-
tection circuit will not work, which may
cause a fire.
! When connecting cables, make sure that the
cables do not come into contact with hot
areas of the vehicle body.
There is a risk of a fire or electric shock.
! Do not wire cables using extension cords.
Doing so may cause the cable to overheat,
resulting in a fire or electric shock.
English
Precautions
3
Section
Precautions
Engb
3