Pioneer VSX-1018AH-S - Manual (Page 79)

Additional information 13
79
En
No sound from the surround or
center speakers. • Check that the Stereo listening mode or the Front Stage Surround Advance mode isn’t selected;
select one of the surround listening modes (see Listening in surround sound on page 29).
• Check that the surround/center speakers are not set to NO (see Speaker Setting on page 48).
• Check the channel level settings (see Channel Level on page 48).
• Check the speaker connections (see Connecting the speakers on page 20).
No sound from surround back
speakers. • Check that the surround back speakers are set to LARGE or SMALL (see Speaker Setting on
page 48).
• Make sure surround back processing is set to SBch ON (see Using surround back channel
processing on page 33).
• If the source is Dolby Surround EX or DTS-ES with no flag to indicate 6.1 compatibility, then with
surround back processing set to SBch Auto, there will be no sound from the surround back
speakers. In this case, set to SBch ON (see Using surround back channel processing on page 33).
• If the source does not have 6.1 playback channels, make sure that surround back processing is set
to SBch ON and a surround mode is selected (see Listening in surround sound on page 29).
• Check the speaker connections (see Connecting the speakers on page 20). If only one surround
back speaker is connected, make sure it’s connected to the left channel speaker terminal.
No sound from subwoofer. • Check that the subwoofer is connected properly, switched on and the volume turned up.
• If your subwoofer has a sleep function, make sure it is switched off.
• Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 48).
• The crossover frequency may be set too low; try setting it higher to match the characteristics of
your other speakers (see Speaker Setting on page 48).
• If there is very little low frequency information in the source material, change your speaker settings
to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS (see Speaker Setting on
page 48).
• Check that the LFE channel is not set to OFF, or a very quiet setting (see Setting the Audio options
on page 69).
• Check the speaker level settings (see Channel Level on page 48).
No sound from one speaker. • Check the speaker connection (see Connecting the speakers on page 20).
• Check the speaker level settings (see Channel Level on page 48).
• Check that the speaker hasn’t been set to NO (see Speaker Setting on page 48).
• The channel may not be recorded in the source. By using one of the advanced effect listening
mode, you may be able to create the missing channel (see Listening in surround sound on page 29).
Sound is produced from
analog components, but not
from digital ones (DVD, LD, CD-
ROM etc.). • Check that the input signal type is set to DIGITAL (see Choosing the input signal on page 32).
• Make sure that the digital input is assigned correctly for the input jack the component is connected
to (see The Input Setup menu on page 65).
• Check the digital output settings on the source component.
• If the source component has a digital volume control, make sure this is not turned down.
• Make sure that the multichannel analog inputs are not selected. Select any other input source.
No sound is output or a noise is
output when Dolby Digital/DTS
software is played back. • Check that your DVD player is compatible with Dolby Digital/DTS discs.
• Check the digital output settings of your DVD player. Make sure that the DTS signal output is set
to On.
• If the source component has a digital volume control, make sure this is not turned down.
No sound when using the
System Setup or Status menu. • If the HDMI input source is selected, sound is muted until exiting either menu.
• If sound is muted in the sub zone (ZONE 2), it will be restored after exiting the System Setup menu.
Symptom Remedy
VSX-1018AH_HY.book 79 ページ ２００８年４月１６日 水曜日 午後７時２５分