Pioneer VSX-1018AH-S - Manual (Page 19)

Connecting your equipment 03
19
En
1 Connect a coaxial-type
1
digital audio output on
your digital component to the COAXIAL IN 2 (CD)
input.
Use a coaxial cable for the connection.
2 For recording equipment, connect the optical-type
DIGITAL output to a digital input on the recorder.
Use an optical cable to connect to the OPTICAL OUT.
2
About the WMA9 Pro decoder
This receiver has an on-board Windows Media™ Audio 9
Professional
3 (WMA9 Pro) decoder, so it is possible to
playback WMA9 Pro-encoded audio using a coaxial or
optical digital connection when connected to a WMA9
Pro-compatible player. However, the connected PC, DVD
player, set-top box, etc. must be able to output WMA9 Pro
format audio signals through a coaxial or optical digital
output.
Connecting analog audio sources
This receiver features two stereo audio-only inputs. One
of these inputs (CD-R) has corresponding outputs for use
with audio recorders.
• Connect the analog audio outputs of the source
component to one of the AUDIO inputs.
Connect using a stereo RCA/phono jack audio cable.
• If you’re connecting a tape deck, MD recorder, etc.,
connect the analog audio outputs (OUT) to the
analog audio inputs on the recorder.
Connecting a component to the front
panel inputs
The front panel inputs comprise a composite video jack
(VIDEO), stereo analog audio inputs (AUDIO L/R) and an
optical digital audio input (DIGITAL IN). You can use
these connections for any kind of audio/video
component, but they are especially convenient for
portable equipment such as camcorders, video games
and portable audio/video equipment.
• Push down on the PUSH OPEN tab to access the
front video connections.
• Select these inputs by pressing VIDEO or using
INPUT SELECT (remote) to select VIDEO.
Note
1 • If your digital component only has an optical digital output, you can connect it to one of the optical inputs on this receiver using an optical cable. When
you set up the receiver you’ll need to tell the receiver which input you connected the component to (see also The Input Setup menu on page 65).
• The digital outputs from other components can be connected to any spare digital audio inputs on this receiver. You can assign them when setting up
the receiver (see also The Input Setup menu on page 65).
2 In order to record some digital sources, you must make analog connections as explained in Connecting analog audio sources below.
3 • Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
• With WMA9 Pro, sound problems may occur depending on your computer system. Note that WMA9 Pro 96 kHz sources will be downsampled to 48 kHz.
A
I CH IN SPEAKERS B
CD CD-R
ANTENNA
PRE OUT
DVR1
IN IN IN
Y
P B
P R
IN OUT
OUT
DVR2 ZONE 2
IN
IN OUT
MONITOR OUT MONITOR OUT
FM UNBAL 75
COMPONENT VIDEO
OUT
OUT
OUT OUT FRONT CENTER
FRONT CENTER SURROUND SURROUND BACK / R L R L R
SURROUND SURROUND BACK
SURROUND SURROUND BACK
(Single)
1 IN 2 IN 3 IN
ASSIGNABLE
3 1 -
AM LOOP
SELECTABLE SEE INSTRUCTION MANUAL
SELECTABLE VOIR LE MODE D'EMPLOI
L
(Single)
SUBWOOFER CD-R
IN OUT
PLAY
OUT
IN
REC
R L
AUDIO IN/OUT
VSX-1018AH
Tape deck, etc.
PHONES
AUTO SURR/ STREAM DIRECT HOME THX STANDARD
SURROUND ADVANCED
SURROUND STEREO/ A.L.C.
ST + ST – SPEAKERS ON/OFF CONTROL MULTI-ZONE
MCACC SETUP MIC iPod DIRECT USB DIGITAL IN AUDIO R L VIDEO VIDEO INPUT iPod DIRECT USB DIGITAL IN AUDIO R L VIDEO VIDEO INPUT
VIDEO OUTPUT DIGITAL OUT
PUS H OPE N
MCACC SETUP MIC DIGITAL IN AUDIO R L VIDEO VIDEO INPUT iPod DIRECT USB
TV game, video camera, etc.
VSX-1018AH_HY.book 19 ページ ２００８年４月１６日 水曜日 午後７時２５分