Pioneer VSX-S510-S User Manual
Page 24
Basic Setup
3
3
24
•
Press
HOME MENU
at any time to exit the Home
Menu. If you cancel the Auto MCACC setup at any
time, the receiver automatically exits and no settings
will be made.
•
The screensaver automatically starts after three
minutes of inactivity.
6
Select ‘Auto MCACC’ from the Home Menu, then press
ENTER
.
•
Mic In!
blinks when the microphone is not connected
to MCACC SETUP MIC jack.
Try to be as quiet as possible after pressing
ENTER
. The
system outputs a series of test tones to establish the
ambient noise level.
7
Follow the instructions on-screen.
•
Make sure the microphone is connected.
•
Make sure the subwoofer is on and the volume is
turned up.
•
When using surround back speakers, turn on the
power to the amplifier to which the surround back
speakers are connected, and adjust the sound level to
the desired level (VSX-S510 only).
8
Wait for the test tones to finish.
A progress report is displayed on-screen while the
receiver outputs test tones to determine the speakers
present in your setup. Try to be as quiet as possible while
it’s doing this.
•
For correct speaker settings, do not adjust the volume
during the test tones.
9
Confirm the speaker configuration.
The configuration shown on-screen should reflect the
actual speakers you have.
•
With error messages (such as Too much ambient
noise
) select RETRY after checking for ambient noise
(see
Other problems when using the Auto MCACC
).
If the speaker configuration displayed isn’t correct, use
/
to select the speaker and
/
to change the
setting. When you’re finished, go to the next step.
If you see an error message (ERR) in the right side
column, there may be a problem with the speaker
connection. If selecting RETRY doesn’t fix the problem,
turn off the power and check the speaker connections.
10
Make sure ‘OK’ is selected, then press
ENTER
.
If the screen in step 9 is left untouched for 10 seconds
and
ENTER
is not pressed in step 10, the Auto MCACC
setup will start automatically as shown.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings for channel level, speaker
distance, X.Over, and Acoustic Calibration EQ.
Again, try to be as quiet as possible while this is
happening. It may take 1 to 3 minutes.
11
The Auto MCACC setup has finished! You return to the
Home Menu.
The settings made in the Auto MCACC setup should give
you excellent surround sound from your system, but it is
also possible to adjust these settings manually using the
Home Menu (starting on
).
Note
•
Depending on the characteristics of your room, sometimes
identical speakers with cone sizes of around 12 cm will end
up with different size settings. You can correct the setting
manually using the
•
The subwoofer distance setting may be farther than the
actual distance from the listening position. This setting
should be accurate (taking delay and room characteristics
into account) and generally does not need to be changed.
H o m e M e nu
1 . Au t o M C AC C
2 . M a nu a l S P S e t u p
3 . I n p u t A s s i g n
4 . Au t o Pow e r D ow n
5 . H D M I S e t u p
6 . N e t wo r k S t a n d by
7 . M H L S e t u p
8 . S p e a k e r S y s t e m
9 . O S D S e t u p
H o m e M e nu
1 . Au t o M C AC C
2 . M a nu a l S P S e t u p
3 . I n p u t A s s i g n
4 . Au t o Pow e r D ow n
5 . H D M I S e t u p
VSX-S510
VSX-S310
1 . Au t o M C AC C
N ow A n a ly z i n g
E nv i ro n m e n t C h e ck
A m b i e n t N o i s e
S p e a k e r Y E S / N O
R e t u r n
1 . Auto MCACC
Check
Return
10:Next
Front
Center
Surr
Surr. Back
Subwoofer
[ YES ]
[ YES ]
[ YES ]
[YESx2]
[ YES ]
1 . Auto MCACC
Check
OK
Return
10:Next
Front
Center
Surr
Subwoofer
[ YES ]
[ YES ]
[ YES ]
[ YES ]
OK
VSX-S510
VSX-S310
1 . Au t o M C AC C
N ow A n a ly z i n g
S u r ro u n d A n a ly z i n g
S p e a k e r S y s t e m
X . O v e r
S p e a k e r D i s t a n c e
C h a n n e l L ev e l
A c o u s t i c C a l E Q
Return