Konica Minolta bizhub PRESS 1250P - Manual (Page 3)

R e v , 1 . 0 , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , . . . . . . . . . . . . . . . , , , J u l y 2 0 1 2
1. Safety
THE SAFETY OF YOU AND OTHERS IS VERY IMPORTANT TO
GBC. IMPORTANT SAFETY MESSAGES AND INFORMATION
ARE CONTAINED IN THIS MANUAL AS WELL AS ON THE
MACHINE ITSELF. PLEASE MAKE SURE YOU CAREFULLY
READ AND UNDERSTAND ALL OF THESE BEFORE
OPERATING THE MACHINE.
THE SAFETY ALERT SYMBOL PRECEDES EACH
SAFETY MESSAGE IN THIS OPERATION
INSTRUCTIONS MANUAL. THIS SYMBOL
INDICATES A POTENTIAL PERSONAL SAFETY
HAZARD THAT COULD HURT YOU OR OTHERS
THE FOLLOWING PICTORIAL IS FOUND ON THE GP-502.
This safety message means you could
get an electrical shock because
disconnecting power from this section
does not cut off power from adjacent
sections of the machine.
This safety message means that you
might get seriously hurt or killed if you
open the product and expose yourself to
hazardous voltage. NEVER remove the
screwed on covers.
ALWAYS refer service
• Use the GP-502 only for its intended purpose of punching
and binding books using paper and covers according to the
indicated specifications.
• Retain this Operation Instructions manual for future use.
CAUTION: THE PRINTER ON/OFF SWITCH DOES
NOT CUT OFF POWER FROM THE BINDER.
CAUTION: THE PUNCH ON/OFF SWITCH DOES
NOT CUT OFF POWER FROM THE BINDER.
• The GP-502 must be connected to a supply voltage
corresponding to the electrical rating of the machine
operation instructions (also listed on the serial number label).
• The grounding plug is a safety feature and will only fit into
the proper grounding-type power outlet. If you are unable to
insert the plug into an outlet, contact a qualified electrician to
have a suitable outlet installed.
• Do not alter the plug on the end of the cordset of the GP-502.
It is provided for your safety.
• Unplug the GP-502 before moving the machine or whenever
the machine is not in use for an extended period of time.
• Do not operate the GP-502 if the machine has a damaged
power supply cord or plug. Do not operate the machine after
any malfunction. Do not operate the machine in case of
liquid spills, or if the machine has been damaged in any
other way.
•
Do not overload electrical outlets.
FCC NOTE
(THE FOLLOWING NOTE ONLY APPLIES TO THE UNITS
RATED 115V 60HZ.)
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
Operation Manual, may cause harmful interference with radio
communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his/her own expense.
Safety messages
CAUTION: CHANGES OR MODIFICATIONS NOT
EXPRESSLY APPROVED BY GENERAL BINDING
CORPORATION COULD VOID YOUR AUTHORITY TO
OPERATE THE EQUIPMENT.
Canada Class A Notice - Avis Canada, Classe A
This Class A digital apparatus complies with Canadian ICES-3.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
MAIN CORDSET SELECTION
(THE FOLLOWING NOTE ONLY APPLIES ONLY TO THE UNITS
RATED 230V 50HZ, AND LOCATED IN THE EUROPEAN
UNION)
CAUTION: WHEN CHOOSING A DETACHABLE LINE
CORD FOR USE WITH YOUR GP-502,
ALWAYS FOLLOW THE FOLLOWING PRECAUTIONS
The cordset consists of three parts: the attachment plug, the cord
and the appliance inlet. Each of these components must have
European regulatory safety approvals.
The following minimum electrical ratings for the specific cordset
are published for safety purposes.
DO NOT USE CORDSETS THAT DO NOT MEET THE
FOLLOWING MINIMUM ELECTRICAL REQUIREMENTS.
PLUG: 3 amperes, 250 volts, 50/60 Hz, Class 1, 3 conductor,
European safety approved.
CORD: Type H05VV-F3G0.75, Harmonized (< HAR>). The "< >"
symbols indicate cord approved according to appropriate
European standard (NOTE: "HAR" may be substituted for
approval mark of European safety agency that approved the cord.
An example would be "< VDE >").
APPLIANCE CONNECTOR: 3 amperes, 250 volts, 50/60 Hz,
European safety approved, Type IEC 320. The cordset shall not
exceed 3 meters in length. A cordset with component electrical
ratings
3