beautypg.com

Serial ata hard disk drive connection, Sata6, Ich8r raid controller – Asus Motherboard P5B-E User Manual

Page 51: Asus p5b-e 2-27, P5b-e sata connectors sata1, Sata3, Sata4 sata2, Sata5, Connector color setting use

background image

ASUS P5B-E

2-27

3. ICH8R Serial ATA connectors (7-pin SATA1 [red], SATA2 [red], SATA3

[black], SATA4 [black], SATA5 [red], SATA6 [red])
These connectors are for the Serial ATA signal cables for Serial ATA hard disk

drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID

1, RAID 5, RAID 10 configuration with the Intel

®

Matrix Storage Technology

through the onboard Intel

®

ICH8R RAID controller.

P5B-E

®

P5B-E SATA connectors

SATA1

G

ND

RS

AT

A_

TX

P3

RS

AT

A_

TX

N3

G

ND

RS

AT

A_

RX

P3

RS

AT

A_

RX

N3

G

ND

G

ND

RS

AT

A_

TX

P1

RS

AT

A_

TX

N1

G

ND

RS

AT

A_

RX

P1

RS

AT

A_

RX

N1

G

ND

SATA3

G

ND

RS

AT

A_

TX

P4

RS

AT

A_

TX

N4

G

ND

RS

AT

A_

RX

P4

RS

AT

A_

RX

N4

G

ND

SATA4

SATA2

G

ND

RS

AT

A_

TX

P2

RS

AT

A_

TX

N2

G

ND

RS

AT

A_

RX

P2

RS

AT

A_

RX

N2

G

ND

SATA5

G

ND

RS

AT

A_

TX

P5

RS

AT

A_

TX

N5

G

ND

RS

AT

A_

RX

P5

RS

AT

A_

RX

N5

G

ND

G

ND

RS

AT

A_

TX

P6

RS

AT

A_

TX

N6

G

ND

RS

AT

A_

RX

P6

RS

AT

A_

RX

N6

G

ND

SATA6

• These connectors are set to Standard IDE mode by default. In Standard

IDE mode, you can connect Serial ATA boot/data hard disk drives to these

connectors. If you intend to create a Serial ATA RAID set using these

connectors, set the [Configure SATA as] item in the BIOS to [RAID]. See

section “4.3.5 IDE Configuration” on page 4-14 for details.

• For RAID 5, use at least three hard disk drives. For RAID 10, use at least

four hard disk drives. Use two to four Serial ATA hard disk drives for each

RAID 0 or RAID 1 set.

• You must install Windows

®

2000 Service Pack 4 or the Windows

®

XP

Service Pack 1 before using Serial ATA hard disk drives. The Serial ATA

RAID feature (RAID 0/RAID 1/RAID 5/RAID 10) is available only if you are

using Windows

®

2000/XP or later version.

• When using the connectors in Standard IDE mode, connect the primary (boot)

hard disk drive to the SATA1/2/5/6 connector. Refer to the table below for

the recommended SATA hard disk drive connections.

Serial ATA hard disk drive connection

Connector

Color

Setting

Use

SATA1/2/5/6

Red

Master

Boot disk

SATA3/4

Black

Slave

Data Disk

P5B-E

®

P5B-E SATA connectors

SATA1

G

ND

RS

AT

A_

TX

P3

RS

AT

A_

TX

N3

G

ND

RS

AT

A_

RX

P3

RS

AT

A_

RX

N3

G

ND

G

ND

RS

AT

A_

TX

P1

RS

AT

A_

TX

N1

G

ND

RS

AT

A_

RX

P1

RS

AT

A_

RX

N1

G

ND

SATA3

G

ND

RS

AT

A_

TX

P4

RS

AT

A_

TX

N4

G

ND

RS

AT

A_

RX

P4

RS

AT

A_

RX

N4

G

ND

SATA4

SATA2

G

ND

RS

AT

A_

TX

P2

RS

AT

A_

TX

N2

G

ND

RS

AT

A_

RX

P2

RS

AT

A_

RX

N2

G

ND

SATA5

G

ND

RS

AT

A_

TX

P5

RS

AT

A_

TX

N5

G

ND

RS

AT

A_

RX

P5

RS

AT

A_

RX

N5

G

ND

G

ND

RS

AT

A_

TX

P6

RS

AT

A_

TX

N6

G

ND

RS

AT

A_

RX

P6

RS

AT

A_

RX

N6

G

ND

SATA6

This manual is related to the following products: