Vollrath F144 - Manual (Page 14)

Owner’s Manual #513677 8 F144I2, SF144I2 and SF121I2 Model Machines
B. DISASSEMBLY OF BLENDER
1. Remove the clear acrylic splash guard from the
blender.
2. Remove the blender’s agitator from the agitator
shaft. Grasp the agitator shaft in one hand and
turn the agitator in a clockwise direction with the
other hand (Fig. 3-7)
3.4 CLEANING DISASSEMBLED PARTS
Disassembled machine parts require complete cleaning,
sanitizing and air drying before assembling. Local and state
health codes will dictate the procedure required. Some
state health codes require a four sink process (pre-wash,
wash, rinse, sanitize, air dry), while others require a three
sink process (without the pre-wash step). The following
procedures are a general guideline only. Consult your
local and state health codes for the procedures required
in your location.
A. Prepare Stera-Sheen or equivalent cleaner in
2 gallons of 90° to 110°F (32° to 43°C) water
following manufacturers instructions. Place all
parts in the solution and clean with provided
brushes.
B. Rinse all parts with clean 90° to 110°F (32° to
43°C) water.
C. Wash the hopper and freezing cylinder with the
Stera-Sheen solution and brushes provided.
D. Clean the rear seal surfaces from the inside of the
freezing cylinder with the Stera-Sheen Solution.
3.5 SANITIZING MACHINE PARTS
A. Use Stera-Sheen or equivalent sanitizing solution
mixed according to manufacturer’s instructions to
provide a 100 parts per million strength solution.
Mix sanitizer in quantities of no less than 2
gallons of 90° to 110°F (32°C to 43°C) water. Any
sanitizer must be used only in accordance with
the manufacturer’s instructions.
B. Place all parts in the sanitizing solution for 5
minutes, then remove and let air dry completely
before assembling in machine.
3.6 CLEANING THE MACHINE
The exterior should be kept clean at all times to preserve
the luster of the stainless steel. A high grade of stainless
steel has been used on the machine to ease cleanup. To
remove spilled or dried mix, wash the exterior with 90° to
110°F (32°C to 43°C) Stera-Sheen solution or equivalent
cleaner and wipe dry.
Do not use highly abrasive materials, as they will mar the
fi nish. Use a soft cloth or sponge to apply the solution.
For best results, wipe with the grain of the steel.
A. Clean the rear seal surface from inside of the
freezing cylinder.
B. Using sanitizing solution and the large barrel
brush provided, sanitize the freezing cylinder by
dipping the brush in the sanitizing solution and
brushing the inside of the freezing cylinder.
NOTE
Do not let sanitizing solution sit overnight in the
freezing cylinder.
C. Remove the drip tray by pulling from the front
panel. Clean and replace the drip tray.
3.7 ASSEMBLING MACHINE
To assemble the machine parts, refer to the following steps:
NOTICE
Petrol-Gel sanitary lubricant or equivalent must be
used when lubrication of machine parts is specifi ed.
NOTICE
The United States Department of Agriculture and
the Food and Drug Administration require that lubri-
cants used on food processing equipment be certi-
fi ed for this use. Use lubricants only in accordance
with the manufacturer’s instructions.
A. Assemble all o-rings onto parts dry, without
lubrication. Then apply a thin fi lm of sanitary
lubricant to exposed surfaces of the o-rings.
CAUTION
Hazardous Moving Parts
Revolving blender agitator shaft can grab and
cause injury. Remove watches and jewelry prior
to operating the blender. Keep hands and clothing
away from revolving agitator. The Blender Power
switch must be placed in the OFF position when
not in use.
Figure 3-7 Removing Agitator