Young AQ Wind Monitor Meets EPA - PSD Model 05305 - Manual (Page 2)

Page 1
05305L-90(G)
MODEL 05305L
WIND MONITOR-AQ
with 4-20mA OUTPUTS
INTRODUCTION
The Wind Monitor measures horizontal wind speed and direction.
Developed for air quality applications, it is accurate, sensitive, and
corrosion resistant. The main housing, nose cone, propeller, and
other internal parts are injection molded U.V. stabilized plastic. The
tail section is lightweight expanded polystyrene. Both the propeller
and vertical shafts use stainless steel precision grade ball
bearings. Bearings have shields to help exclude contamination
and moisture.
Propeller rotation produces an AC sine wave signal with frequency
proportional to wind speed. Internal circuitry converts the raw
signal to 4 to 20 mA current output over specified wind speed
range.
Vane position is sensed by a 10K ohm precision conductive plastic
potentiometer. This signal is also converted to 4 to 20mA output.
The instrument mounts directly on a standard one inch pipe,
outside diameter 34 mm (1.34"). An orientation ring is provided so
the instrument can be removed for maintenance and re-installed
without loss of wind direction reference. Both the sensor and the
orientation ring are secured to the mounting pipe by stainless steel
band clamps. Electrical connections are made in a junction box at
the base.
INITIAL CHECK-OUT
When the Wind Monitor is unpacked it should be checked carefully
for any signs of shipping damage.
Remove the plastic nut on the propeller shaft. Install the propeller
on the shaft with the serial number of the propeller facing forward
(into the wind). The instrument is aligned, balanced and fully
calibrated before shipment; however, it should be checked both
mechanically and electrically before installation. The vane and
propeller should easily rotate 360° without friction. Check vane
balance by holding the instrument base so the vane surface
is horizontal. It should have near neutral torque without any
particular tendency to rotate. A slight imbalance will not degrade
performance.
INSTALLATION
Proper placement of the instrument is very important. Eddies from
trees, buildings, or other structures can greatly influence wind
speed and wind direction observations. To get meaningful data for
most applications, locate the instrument well above or upwind from
obstructions. As a general rule, the air flow around a structure is
disturbed to twice the height of the structure upwind, six times the
height downwind, and up to twice the height of the structure above
ground. For some applications it may not be practical or necessary
to meet these requirements.
FAILURE TO PROPERLY GROUND THE WIND MONITOR
MAY RESULT IN ERRONEOUS SIGNALS
OR TRANSDUCER DAMAGE.
Grounding the Wind Monitor is vitally important. Without proper
grounding, static electrical charge can build up during certain
atmospheric conditions and discharge through the transducers.
This discharge may cause erroneous signals or transducer failure.
To direct the discharge away from the transducers, the mounting
post assembly in which the transducers are mounted is made with
a special anti-static plastic. It is important that the mounting post
be connected to a good earth ground. There are two ways this
may be accomplished. First, the Wind Monitor may be mounted
WIND SPEED SPECIFICATION SUMMARY
Range 0 to 50 m/s (112 mph)
Sensor 20 cm diameter 4-blade helicoid carbon
fiber thermoplastic propeller, 30.7 cm air
passage per revolution
Distance Constant 2.1 m (6.9 ft.) for 63% recovery
Threshold Sensitivity 0.4 m/s (0.9 mph)
Transducer
Centrally mounted stationary coil,
2K Ohm nominal DC resistance
Output Signal 4 to 20 mA = 0 to 100 m/s
WIND DIRECTION (AZIMUTH) SPECIFICATION SUMMARY
Range 360° mechanical, 355° electrical (5° open)
Sensor Balanced vane, 48.3 cm (19 in) turning radius.
Damping Ratio 0.45
Delay Distance 1.2 m (3.9 ft) for 50% recovery
Threshold Sensitivity 0.5 m/s (1.0 mph) at 10° displacement
Damped Natural
Wavelength
4.9 m (16.1 ft)
Undamped Natural
Wavelength
4.4 m (14.4 ft)
Transducer Precision conductive plastic potentiometer,
10K ohm resistance (±20%), 0.25%
linearity, life expectancy 50 million
revolutions, rated 1 watt at 40°C, 0 watts
at 125°C
Output Signal 4 to 20 mA for 0 to 360°
GENERAL
Power Requirement: 12 - 30 VDC
Operating Temp:
-50 to 50°C (-58 to 122°F)