Installing your mobile base, Sawstop contractor mobile base 2 – SawStop Mobile Base User Manual
Page 3
SawStop Contractor Mobile Base 2
Installing Your Mobile Base
Mobile Base Hardware Pack
Nylon Hex Nuts,
M6 (2)
4
Lock Washers,
M8 x 13.6 (4) 6
Flange Lock Nuts,
M6 (2)
9
Shoulder Socket Screw,
M8 x 17.7 (1) 15
Shoulder Socket Screw,
M8 x 15.7 (1) 13
Nylon Hex Nut,
M8 (1)
19
Cap Nut,
M8 (1) 20
Extension Spring,
(1)
17
Hex Bolts,
M8 x 40 (2)
8
Caster Nuts,
3/8” thread (2) 12
Wave Washer,
M10.5 x 14.5 (1) 16
Short Fixed Wheel Axle,
M6 x 67.6 (1)
1
Long Fixed Wheel Axle,
M6 x 73.8 (1)
2
Washers,
M6 x 16 (4) 3
Button Head Socket
Screws, M8 x 20 (4)
5
Washers,
M8 x 18 (4)
7
Hex Screw,
M8 x 30 (1) 14
Release Lever
Locking Screw (1) 18
Lock Washers,
M10.5 x 17 (2) 11
Washers,
M10.5 x 25 (2) 10
Low
er
Raise
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
1. Nev
er plac
e finge
rs, toes
or othe
r
body p
arts un
der the
mobile
base.
2. Alw
ays use
the saw
and the
mobile
base o
n a leve
l surfac
e.
3. Low
er the s
aw befo
re usin
g
saw w
hen it is
raised
off
4. Low
er the
saw slo
drop ba
ck to.
!
WARNIN
G
1
4
3
Installing Your Mobile Base
Fig. 1
Fig. 2
Fig. 3
1. Locate all of the mobile base components shown on page 1. All of the hardware
needed to install the mobile base is located on the mobile base hardware
pack (see Fig. 1). In order to easily identify the hardware used in each of
the following steps, the different pieces of hardware are numbered on the
hardware pack and in the figures. If you are missing the hardware pack or any
of the other mobile base components, call the SawStop Service Department
at 503-682-6222 for replacements.
You will need the following tools to complete the mobile base installation:
• two 10 mm wrenches
• two 13 mm wrench
• a 14 mm wrench
• a 5 mm hex key
Note: The stand for your contractor saw must be fully assembled before installing the mobile base.
2. Take the wheel support and mount one of the
3 inch wheels to the end furthest from the foot
pedal. Use the short axle, one M6 washer,
and one M6 nylon hex nut to mount the wheel
to the support as shown in Fig. 2. Fully tighten
the nut using a 10 mm wrench and a 5 mm
hex key.
3. Mount the other 3 inch wheel to the other end of the wheel support. Use the long axle, one M6 washer, and
one M6 nylon hex nut to mount the wheel to the support as shown in Fig. 3. Do not tighten the nut because it
will be removed in a later installation step.
2
4
3
foot pedal
3 inch
wheel
3 inch
wheel
foot pedal