Beijer Electronics BFI-H2 V1.12 - Manual (Page 68)

User Guide Revision 1.12
68
14. Parameter Change Tables
The following tables can be used to enter parameter changes made to the drive as a result of commissioning and to provide future reference.
P1-01 Max Speed Limit P3-03 User PID Differential Time Constant
P1-02 Min Speed Limit P3-04 User PID Operating Mode
P1-03 Acceleration Ramp Time P3-05 User PID Reference Select
P1-04 Deceleration Ramp Time P3-06 User PID Digital Reference
P1-05 Stop Mode P3-07 User PID Controller Output High Limit
P1-06 Energy Optimiser P3-08 User PID Controller Output Low Limit
P1-07 Motor Rated Voltage P3-09 User PID Output Control
P1-08 Motor Rated Current P3-10 User PID Feedback Select
P1-09 Motor Rated Frequency P3-11 PID Error To Enable Ramps
P1-10 Motor Rated Speed P3-12
PID Feedback Value Display Scaling
Factor
P1-11 V/F Voltage Boost P3-13 PID Feedback Wake-Up Level
P1-12 Control Mode P3-14 Standby Active Speed
P1-13 Digital Inputs Function Select P3-15 2
nd
User PID Digital Reference
P1-14 Extended Menu Access Code P4-02 Motor Parameter Auto-Tune
P2-01 Preset Speed 1 P5-01 Fieldbus Drive Address
P2-02 Preset Speed 2 P5-03 Modbus / Bacnet Baudrate
P2-03 Preset Speed 3 P5-04 Modbus / Bacnet Data Format
P2-04 Preset Speed 4 P5-05 Comms Loss Timeout
P2-05 Preset Speed 5/ Clean Speed 1 P5-06 Communications Loss Action
P2-06 Preset Speed 6/ Clean Speed 2 P5-07 Field-Bus Ramp Control
P2-07 Preset Speed 7/ Boost Speed 1 P5-08 Any-Bus Output Process Data 4
P2-08 Preset Speed 8/ Boost Speed 2 P6-01 Firmware Upgrade Enable
P2-09 Skip Frequency Centrepoint P6-02 Auto Thermal Management
P2-10 Skip Frequency Band P6-03 Auto-Reset Delay Time
P2-11 Analog Output 1 Function Select P6-04 User Relay Hysteresis Band
P2-12 Analog Output 1 Format P6-10 Enable PLC Operation
P2-13 Analog Output 2 Function Select P6-11 Speed Hold Time On Enable
P2-14 Analog Output 2 Format P6-12 Speed Hold Time On Disable
P2-15 User Relay 1 Output Function Select P6-18 DC Injection Braking Voltage
P2-16 User Relay 1 Upper Limit P6-22 Reset Cooling Fan Run-Time
P2-17 User Relay 1 Lower Limit P6-23 Reset kWh Meter
P2-18 User Relay 2 Output Function Select P6-24 Service Time Interval
P2-19 User Relay 2 Upper Limit P6-25 Reset Service Indicator
P2-20 User Relay 2 Lower Limit P6-26 Analog Output 1 Scaling
P2-21 Display Scaling Factor P6-27 Analog Output 1 Offset
P2-22 Display Scaling Source P6-28 P0-80 Display Value Index
P2-23 Zero Speed Holding Time P6-29 Save User Parameters As Default
P2-24 Effective Switching Frequency P6-30 Level 3 Access Code
P2-25 Fast Deceleration Ramp Time P7-01 Rs Value
P2-26 Spin Start Enable P7-04 Magnetizing Current
P2-27 Standby Mode P7-11 Pulse Width Minimum Limit
P2-28 Slave Speed Scaling Control P7-12 V/F Mode Magnetising Period
P2-29 Slave Speed Scaling Factor P8-01 Stir Interval Time
P2-30 Analog Input 1 Format P8-02 Stir Active Time
P2-31 Analog Input 1 Scaling P8-03 Clean Function Setup
P2-32 Analog Input 1 Offset P8-04 Clean Time Setup
P2-33 Analog Input 2 Format P8-05 Clean Ramp Time
P2-34 Analog Input 2 Scaling P8-06 Current Monitor Mode Enable
P2-35 Analog Input 2 Offset P8-07 Current Bandwidth
P2-36 Start Mode Select P8-08 Current Monitor Trip Delay Time
P2-37 Keypad Restart Speed P8-09 Fire Mode Logic
P2-38 Mains Loss Stop Control P8-10 Fire Mode Speed
P2-39 Parameter Lock P8-11 Bypass Mode On Fault
P2-40
Extended Parameter Access Code
Definition
P8-12 Bypass Mode On Fire
P3-01 User Pid Proportional Gain P8-13 Bypass Contactor Change Over Time
P3-02 User PID Integral Time Constant P8-14 Pump Staging Function Select