Beijer Electronics BFI-H2 V1.12 - Manual (Page 47)

User Guide Revision 1.12
47
9. Parameters
9.1. Parameter Set Overview
The drive Parameter set consists of 9 groups as follows:
 Group 1 – Basic Parameter Set

Group 2 – Extended Parameter Set

Group 3 – User PID Control Parameter Set
 Group 4 – Motor Control Parameters

Group 5 – Field Bus Communications Parameter Set

Group 6 – Reserved (Advanced Features: See advanced user guide)

Group 7 – Reserved (Not Available)

Group 8 – HVAC Specific Functions Parameter Set
 Group 9 –Advanced Drive Control Logic (Advanced Features: See advanced user guide)

Group 0 –Monitoring and Diagnostic Parameters (Read Only)
When the drive is reset to factory defaults, or is in its factory supplied state, only Group 1 Parameters can be accessed. In order to allow access
to parameters from the higher level groups, P1-14 must be set to the same value as P2-40 (Default setting = 101). With this setting, parameter
groups 1 – 5 and group 8 can be accessed, along with the first 39 parameters in Group 0. These parameters are listed in the tables below.
For advanced parameter access, P1-14 can be set to the same value as P6-30 (Default setting = 201), which allows access to all parameter
groups and ranges. Advanced parameter descriptions are listed in the advanced user guide.
Values given in brackets () are default settings for horsepower rated drive models.
9.2. Parameter Group 1 – Basic Parameters
Par Parameter Name Minimum Maximum Default Units
P1-01 Maximum Speed Limit P1-02 120.0 50.0 (60.0) Hz / Rpm
Maximum output frequency or motor speed limit – Hz or rpm.
If P1-10 >0, the value entered / displayed is in Rpm
P1-02 Minimum Speed Limit 0.0 P1-01 0.0 Hz / Rpm
Minimum speed limit – Hz or RPM.
If P1-10 >0, the value entered / displayed is in Rpm
P1-03 Acceleration Ramp Time 0.0 6000.0 30.0 Seconds
Acceleration ramp time from 0 to base speed (P-1-09) in seconds.
P1-04 Deceleration Ramp Time 0.0 6000.0 30.0 Seconds
Deceleration ramp time from base speed (P1-09) to standstill in seconds. When set to zero, fastest possible ramp time without trip is
activated
P1-05 Stop Mode Select 0 1 0 -
0 : Ramp To Stop. When the enable signal is removed, the drive will ramp to stop, with the rate controlled by P1-04 as described
above.
1 : Coast to Stop. When the enable signal is removed the motor will coast (freewheel) to stop
P1-06 Energy Optimiser 0 1 0 0
0 : Disabled
1 : Enabled. When enabled, the Energy Optimiser attempts to reduce the overall energy consumed by the drive and motor when
operating at constant speeds and light loads. The output voltage applied to the motor is reduced. The Energy Optimiser is intended
for applications where the drive may operate for some periods of time with constant speed and light motor load.
P1-07 Motor Rated Voltage 0 250 / 500 230 / 400 (460) Volts
This parameter should be set to the rated (nameplate) voltage of the motor (Volts)
P1-08 Motor Rated Current [Drive Dependent] Drive Rated Current 100% drive rated
current
Amps
This parameter should be set to the rated (nameplate) current of the motor
Parameter Range: Frame size 2, min 10% to max 100% of drive rated current
Frame size 3 to 7, min 20% to max 100% of drive rated current
P1-09 Motor Rated Frequency 25 120 50 (60) Hz
This parameter should be set to the rated (nameplate) frequency of the motor
P1-10 Motor Rated Speed 0 7200 0 Rpm
This parameter can optionally be set to the rated (nameplate) rpm of the motor. When set to the default value of zero, all speed
related parameters are displayed in Hz, and the slip compensation for the motor is disabled. Entering the value from the motor
nameplate enables the slip compensation function, and the drive display will now show motor speed in estimated rpm. All speed
related parameters, such as Minimum and Maximum Speed, Preset Speeds etc will also be displayed in Rpm.