A.J. Antunes & Co ICE-H 9700922 - Manual

A. J. ANTUNES & CO. www.ajantunes.com 180 Kehoe Blvd., Carol Stream, Illinois 60188
Chill iCE-1000 (P/N 9700920), iCE-1800 (P/N 9700921), iCE-h (P/N 9700922)
iNSTAllATiON iNSTrUCTiONS
1-877-392-7836 Fax: 630-784-1000 Page 1 of 2 P/N 1011076 Rev. B 11/10
General
If you experience any problems with these instructions,
contact the Technical Service Department at 630-784-1000 or
toll free in the U.S. at 877-392-7854.
Warranty information
All ICE-1000, ICE-1800, and ICE-H units will be free from defects
in materials and workmanship for a period of three years.
Connections
FrESh WATEr CONNECTiONS
Chill ICE units use Super Speedfit® tubing fittings for fresh water
line connections that require no tools. Tubing (copper or plastic) is
simply inserted into the fitting collet to create a secure connection.
The tubing should be inserted approximately 3/4” (1.91 cm) until
it bottoms completely in the fitting to ensure there will be no
leaks. The tubing end to be inserted should be straight and have
a clean round cut. If the tubing is out-of-round, then carefully
make a new cut before inserting into the fitting.
SUmP WATEr CONNECTiONS
Chill ICE units require the use of 3/4” (1.91 cm) PVC pipe for
the sump water connections. It is important to glue all connec-
tions with the multipurpose glue. Follow the specific installation
procedures to make certain there will not be a vacuum block or
any reduction in water flow to the floor drain.
installation
To ensure material compatibility, a multipurpose glue for ABS, PVC,
and CPVC must be used. This will ensure a proper bond between
the 3/4” PVC and the black ABS Sump Water Discharge Inlet.
1. Turn off the ice machine and water supply valve.
2. Install the Chill ICE unit behind or to the side of the ice
machine bin at least 6 inches (15 cm) beneath the height of
the machine’s Sump Water Discharge Outlet (Figure 3).
Figure 1. Connections
Figure 2. Secure Connections
Figure 3. installation of Chill iCE
SUGGESTED MATERIALS AND EQUIPMENT NEEDED:
• (10 ft.) 3/4” PVC Pipe
• (5) 3/4” PVC Elbow Fitting
• (1) 3/4” PVC Tee Fitting
• (10 ft.) Copper Tubing
ICE-1000, ICE-1800: 3/8” OD
ICE-H: 1/2” OD
• (2) Brass Tubing Unions
ICE-1000, ICE-1800: 3/8” OD
ICE-H: 1/2” OD
• Multipurpose glue for ABS, PVC, and CPVC
• Tubing Cutter
• PVC Pipe Cutter
• Screwdriver or Drill with Bits
• Channel-Lock Pliers
• Adjustable Wrench
• Measuring Tape
Fresh Water Outlet
(To Ice Machine)
Sump Water Discharge Inlet
(From Ice Machine)
Sump Water Outlet
(To Floor Drain)
#3
#4
#2
Fresh Water Inlet
(From Wall or Filter)
#1
Cut the tube square and push past
the O-ring to the tube stop
Secure connections are simple
Tube is secured in position
Disconnection is just as easy
Push collet against body
Slide tube out of fitting