PerTronix JBA Exhaust 40-2630 - Manual

INSTALLATION INSTRUCTIONS
**Ins tallation recommendation: J B A recommends in mos t cas es that the vehicle be taken to a reputable exhaus t s hop.
40-2630
2005 Mustang 4.0L V6
Dual exit exhaust system
To get more power out of your Mustang, JBA offers easy to
install 50 state smog legal performance headers and ignition
wires for the 4.0L V6. For more information about these and
other quality performance products from JBA visit us online at
www.jbaheaders.com
JBA Cat4ward® Headers
Part No. 1617S
JBA Powercables™
Part No. 06759
Start:
1. Remove and inventory the JBA
Exhaust System.
2. Disconnect the negative battery
cable and allow the exhaust system to
completely cool.
3. Loosen the clamps attaching the
exhaust to the catalytic converter
assembly. Slide the clamp back to
separate the two.
Parts List:
A.
Y-pipe 1
B. P/S Over axle pipe 1
C. D/S Over axle pipe 1
D. D/S Muffler/Tip assembly 1
E. P/S Muffler/Tip assembly 1
F. Rubber isolator 4
G. Muffler hanger 2
H. 2-1/2" clamps 4
I. Self-tapping screws 4
6/06/07
A
B
C
D
H
H
F
F
E
G G
RECOMMENDED TOOLS:
pry bar
ratchet
15mm deep socket
9/16 deep socket
channel lock pliers
anti-seize
spray lubricant or
penetrating oil
7. Slide the JBA muffler/tip assemblies
(D) and (E) hangers into the rubber
isolators on each side. Be sure to get
the rod into both isolator’s on the new
hangers.
11. Using a soft cloth, wipe the new
JBA tips clean.
12. Reconnect the battery and start the
vehicle to check for leaks.
4. Loosen the clamp connecting the
exhaust pipe to the muffler. Wiggle
the exhaust pipe free from the muffler.
Remove the exhaust pipe from car.
5. Using pliers or a pry bar, slide the
rubber hanger from the hanger rod at
inside, front of muffler (a little lube
helps). Slide the muffler assembly
forward and remove from slip hangers.
6. Bolt the supplied hanger brackets
(G) to the frame on the drivers side
using the supplied self tapping
screws (I). Bolt the brackets in place
with the factory holes. Prongs on the
bracket need to face forward. Then
slide two rubber isolators (F) onto
each hanger so holes align.
8. Install the new over axle pipes (B) and
(C), slip a 2-1/2" clamp (H) onto each
pipe, then insert into muffler/tip
assemblies (D) and (E). Slip two ring
clamps onto the Y-pipe (A), and insert
the Y-pipe into the over axle pipes (B)
and (C).
9. Using the factory clamp, attach the Y-
pipe (A) to the converter assembly.
Adjust to be flat to the ground, and tight
to the converter assembly. Tighten
securely.
10. With the axle pipes (B) and (C) in the
muffler assemblies (D) and (E) adjust
mufflers to be flat, and the tips an equal
distance from the bumper cover, Then
tighten all clamps securely.
Note: This exhaust system is
designed to work with a GT rear
valance, or a V-6 bumper trimmed to
match a GT.
NOTES:
1.) All exhaust systems expand about
1" rearward when exhaust temperature
rises.
We recommend taking the vehicle to a muffler shop and having all slip connections tack welded.