ADIC Scalar 1000 - Manual (Page 22)

twenty
Library Configurations
Scalar 1000
AIT1 AIT2
AIT AIT Total Total
Drives 1 Cartridges Capacity 2 Capacity 3
Base Control Module: 2 to 12 237 16.6TB 23.7TB
With 1 Expansion Module: 2 to 24 492 to 552 38.6TB 55.2TB
With 2 Expansion Modules: 2 to 36 747 to 867 60.7TB 86.7TB
With 3 Expansion Modules: 2 to 48 1002 to 1182 82.7TB 118.2TB
Drive and Performance
Drive Type: AIT1 AIT2
Data Cartridge Capacity AIT AIT2
Native: 35GB 50GB
with 2:1 Compression: 70GB 100GB
Transfer Rate per drive
Native: 180MB/min 360MB/min
with 2:1 Compression: 360MB/min 720MB/min
File Access Time (Avg): 37 seconds with MIC
Data Compression: ALDC (Adaptive Lossless Data Compression)
Data Buffer: 4MB 8MB
Media: AIT1 AIT2
Tape Length: 230m
Recording Density: 116,000 bits/in 167,000 bits/in
Error Correction Code: Read after write enhanced C3 ECC
Operation
Cartridge Change: 6 seconds maximum
Indicators: Password-protected keypad with LCD
menu display
Drive: Status LED and eject buttons
Drive Interface: Fast and Wide SCSI-2 Differential
Library Interface: SCSI-2 Differential
SCSI Connections: 68-pin micro-D
Reliability
Hard Error Rate: Less than 1 in 10 17 bits read
Tape Shelf Life: 30 years minimum (at 20
°
C, 40% RH)
Maintenance: Cleaning not required unless indicated by
drive LEDs
MSBF: Greater than 1,000,000 cartridge changes
MTTR: Less than 30 minutes
Drive MTBF: Greater than 200,000 power-on hours
Field Replaceable: Drives, Power Supplies, Gripper Assembly,
Barcode Reader, Control Electronics Module,
Hot Swappable Drives 4
Diagnostics: Built-In-Test (BIT), Store/Recall Past Events,
“Fault Isolation” Assistance, Self Initiating
Configuration and Calibration Routines
Physical
Control Module: 29.5"W x 47"D x 72"H
(74.9cm x 119.4cm x 182.9cm)
Weight: 1052 lbs. (477Kg) maximum weight
Expansion Module: 29.5"W x 47"D x 72"H
(74.9cm x 119.4cm x 182.9cm)
Weight: 817 lbs (372Kg)
Environmental
Electrical: 115/230 VAC, 1.6kVa
Altitude: 10,000 feet
Temperature: 16
°
C to 32
°
C Operating
Humidity: 15 to 75% Non-Condensing Operating
Compliance and Certification
Year 2000 Compliant
Safety: UL-1950 ITE, CSA950, EN 60950
Emissions: FCC #47 CFR, Part 15, Class A, CSA C108.8M,
EN 55022, Class A
Immunity: IEC (1000-4-2, 3, 4)
International: CE
Software and Platforms
Consult the most recent ADIC Software Compatibility Guide for a
complete list of software and platforms compatible with the Scalar
Library Series.
1 AIT drives offered in pairs.
2 with 2:1 compression. Capacities specified use 230m media. For
170m media reduce capacity by 28.6%
3 With 2:1 compression.
4 Without affecting library operation. Bus integrity must be sustained.
Scalar 1000 / AIT Specifications
Year 2000
Compliant
All specifications subject to change without notice. All products and company names should be considered trademarks of their respective companies.
Scalar ® and ADIC ® are trademarks of Advanced Digital Information Corporation. DLT™ and DLTtape™ are trademarks of Quantum Corporation. AIT™ is a trademark of Sony Corporation ® .
3590 & Magstar are trademarks of IBM Corporation ® . © Copyright 1999 Advanced Digital Information Corporation.