Outback Power Systems GFX International Series Operators Manual - Manual (Page 52)

Specifications
50 900-0112-01-00 Rev B
Default Settings and Ranges (viewed in MATE3)
Table 20 12-Volt Inverter Settings (MATE3)
Field Item Default Minimum Maximum
Sensitivity (see page 14 for increments) 6 0 50
Pulse Length 8 4 20 Search
Pulse Spacing 60 AC cycles 4 AC cycles 120 AC cycles
Input Type Grid Grid or Gen
Input Support Y Y or N
Grid Input AC Limit 25 Aac 2.5 Aac 30 Aac
Gen Input AC Limit 25 Aac 2.5 Aac 30 Aac
AC Input and
Current Limit
Charger AC Limit 5 Aac 0 Aac 6 Aac
LowerVoltage Limit 208 Vac 140 Vac 220 Vac
Upper Voltage Limit 252 Vac 250 Vac 280 Vac
Grid AC Input
Voltage Limits
Transfer Delay 6 AC cycles 0 AC cycles 240 AC cycles
LowerVoltage Limit 208 Vac 140 Vac 220 Vac
Upper Voltage Limit 252 Vac 250 Vac 280 Vac
Transfer Delay 6 AC cycles 0 AC cycles 240 AC cycles
Gen AC Input
Voltage Limits
Connect Delay 0.5 minutes 0.2 minutes 15 minutes
AC Output AC Output 230 Vac 210 Vac 250 Vac
Cut-Out Voltage 10.5 Vdc 9 Vdc 12 Vdc
Low Battery
Cut-In Voltage 12.5 Vdc 10 Vdc 14 Vdc
Absorb Voltage 14.4 Vdc 13 Vdc 16 Vdc
(Absorb) Time 1.0 hours 0.0 hours 24.0 hours
Float Voltage 13.6 Vdc 12 Vdc 15 Vdc
(Float) Time 1.0 hours 0.0 hours 24.0 hours
Battery Charger
Re-Float Voltage 12.5 Vdc 12 Vdc 13 Vdc
Equalize Voltage 14.6 Vdc 14 Vdc 17 Vdc
Battery Equalize
(Equalize) Time 1.0 hours 0.0 hours 24.0 hours
Aux Mode Cool Fan
Remote, Load Shed, Gen Alert, Fault, Vent Fan,
Cool Fan, Divert DC, Divert AC, or AC Drop
(Load Shed) Enable Voltage 11 Vdc 10 Vdc 14 Vdc
(Gen Alert) ON Voltage 11 Vdc 10 Vdc 14 Vdc
(Gen Alert ON) Delay 4 minutes 0 minutes 240 minutes
(Gen Alert) OFF Voltage 14 Vdc 12 Vdc 18 Vdc
(Gen Alert OFF) Delay 9 minutes 0 minutes 240 minutes
(Vent Fan) Enable Voltage 13 Vdc 10 Vdc 16 Vdc
(Vent Fan) Off Period 5 minutes 0 minutes 30 minutes
(Divert DC or AC) Enable Voltage 14.6 Vdc 12 Vdc 16 Vdc
Auxiliary
Output
(Divert DC or AC) Off Delay 30 seconds 0 seconds 240 seconds
Inverter Stacking Stack Mode Master Master, OB Slave L1, 3p Classic B , 3p Classic C
Master Adjust Only 0 0 7
Power Save
Slave Adjust Only 1 1 15
Grid Tie Enable Y Y or N
Sell Voltage 13 Vdc 10 Vdc 15 Vdc Grid-Tie Sell
Grid Tie Window IEEE IEEE or user
Input Voltage 7 -1 -3 1
Output Voltage 7 -1 -3 1 Calibrate
Battery Voltage 8 0.0 -0.2 0.2
7
These values represent an adjustable setting with a total range of 4 Vac. The default value of -1 means the calibration will subtract 1 volt from the measured
value. The range of settings allow up to 1 volt to be added to the measured value, or up to 3 volts to be subtracted from it. The result is also displayed.
8
These values represent an adjustable setting with a range of ± 0.2 Vdc from the measured value. The range of settings allow up to 0.2 volts to be either
added or subtracted from the measured value. The result is also displayed.