Alamo 803350C User Manual
Versa pro, Operator’s manual, Flail mower
©2009 Alamo Group Inc.
$0.00
Published 03/09
Part No.
803350C
OPERATOR’S MANUAL
ALAMO INDUSTRIAL
®
1502 E. Walnut
Seguin, Texas 78155
830-372-3551
Email: [email protected]
FLAIL MOWER
This Operator's Manual is an integral part of the safe operation of this machine and must
be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety
and Operation Instructions contained in this manual before operating the equipment. C01-
Cover
VERSA PRO
Table of contents
Document Outline
- VERSA PRO
- OPERATOR’S MANUAL
- To the Owner/Operator/Dealer
- Alamo Industrial Division is willing to provide
- one (1) AEM Mower Safety Practices Video
- TABLE OF CONTENTS
- Decal Location
- 1. 002369 4 DANGER Multiple-Hazard
- 2. 00753840 2 DANGER Folding Wings/Wings Raised
- 3. 00756004 2 DANGER D/L Shield Missing
- 4. 00756005 2 DANGER Rotating D/L, Entanglement
- 5. 00756007 3 WARNING Use/Repair Shields/Guards
- 6. 00756059 3 DANGER Oil Penetration, Leaks
- 7. 00746485 3 DANGER Cutting Blades, Thrown Objects
- 8. 00746494 1 DANGER Driveline Hazards
- 9. 00758194 3 WARNING Belt/Pulley Pinch Point
- 10. 02962765 2 DANGER Crushing from Folding Hazard
- 11. 002425 3 DANGER Removing Front Shield
- 12. 03200437 1 WARNING Pressurized Tank
- 13. 03200347 REFLCTR SMV Reflector
- 14. 99203 2 REFLCTR Red Reflector Decal
- 15. 99204 4 REFLCTR Yellow Reflector Decal
- 16. 03200286 1 INSTRUCT Hyd Oil and Type
- 17. 03200432 3 INSTRUCT Genuine ALAMO Flail Parts
- 18. 002023 3 INSTRUCT Cutting Height Adjustment
- 19. 000108 3 INSTRUCT Flail Operation
- 20. 000678 2 INSTRUCT Grease Fitting Inside
- 21. 002490 3 INSTRUCT Wing Unit Lube Chart
- 22. 02962748 2 INSTRUCT On/Off Solenoid Switch
- 23. 02965093 1 INSTRUCT Do Not Overspeed Engine
- 24. 00763977 1 INSTRUCT Notice to Owner
- 25. 001650 1 LOGO ALAMO (7.5 x 7)
- 26. 001651 4 LOGO ALAMO IND
- 27. 02960766 3 LOGO ALAMO (4 x 5)
- 28. 002489 3 NAME VERSA PRO (Name)
- 29. nfs (L) 1 SER PLT Left Wing Serial Plate’
- 30. nfs (R) 1 SER PLT Right Wing Serial Plate
- 31. nfs (C) 1 SER PLT Center Mower Serial Plate
- 32. nfs (F) 1 SER PLT VERSA PRO Serial Plate
- 33. 002505 1 INSTRUCT Wing Lowering
- 34. 001830 1 INSTRUCT Lubrication Rear
- 35. 00773723 2 DANGER Peligro, Driveline
- 36. 02977417 1 INSTRUCT Operators Manual Inside
- 37. 00776031 1 ________ Canister, Operations Manual
- 38. 803350C 1 ________ Operator’s Manual, Versa Pro
- 39. 10058000 3 ________ Bolt
- 40. 00024100 6 ________ Flatwasher
- 41. 02959924 3 ________ Locknut
- Decal Description
- Federal Laws and Regulations
- TRACTOR PREPARATION
- 1. Remove the Anti-Sway Bars from tractor and Lower Links.
- 2. Remove the Pins that attach the Lower Links to the Down Links and the Tractor Lugs. Remove the Lower Links. Insert the Pins back into the Down Links and the Tractor Lugs. These Pins will be used when attaching the V-Pro to the tractor.
- 3. Remove the complete Draw Bar and carrier from the Tractor.
- MAINFRAME TO ATTACHMENT FRAME ASSEMBLY
- TRACTOR TO ATTACHMENT FRAME ASSEMBLY
- DRIVELINE ATTACHMENT
- ELECTRICAL CONNECTION AT TRACTOR
- CENTER MOWER ASSEMBLY
- CENTER MOWER ASSEMBLY
- 1. Remove fasteners and shaft protector from end of drive shaft. Lightly grease shaft. Install key and drive shaft pulley. Do not secure at this time. ASM-FL-0052.
- 2. Align all three pulleys. Use spacers and shims provided to achieve alignment, then secure idler arm assembly with cotter pin. Secure drive shaft pulley with fasteners removed in Step 1, above.
- 3. Install drive belt. ASM-FL-0053_A.
- 4. Attach spring. One end is inserted in idler arm spring arm hole; the other end is attached to the long outboard bearing plate bolt.
- INSTALLATION OF CENTER MOWER
- 1. To properly attach center mower to mainframe, align lower links (1) to overarms (2) and anti-sway bar (3). Attach with 7/8" x 5" bolt and 7/8" locknut (4).
- 2. Align toplink (5) with top of A-frame (6) on center mower and retain with pin (7), washers (8), and cotter pins. Attach the other end of the toplink to the mainframe. Install 1" x 4" bolt through safety chain and retain with 1" locknut.
- 3. Continue with driveline by aligning slipclutch and gearbox shaft and slide slipclutch in and tighten bolt. On the other end of driveline pull slide collar back, slip into speed increaser shaft and release slide collar. Move driveline in and out to...
- 4. Level front unit by adjusting top link. Be sure skid shoes are level with ground.
- HYDRAULIC CONNECTIONS
- HOSE CONNECTION AT TRACTOR
- 1. To properly connect hydraulic hoses to tractor, connect right wing hose P/N 02839000 (1), and left wing hose P/N 02839000 (2). ASM-FL-0112.
- 2. Connect center lift hose P/N 02964451 (3) to connection at center of tractor. ASM-FL-0112. This should be the remote valve with "Float" position. Always operate front mower in float detent position.
- HYDRAULIC CONNECTIONS TO CYLINDER
- HYDRAULIC
- FINAL CHECK
- 1. OPERATOR REQUIREMENTS
- 1.3 Tractor Horsepower
- 1.4 Tractor Hydraulics
- 1.5 Front End Weight
- 1.6 Power Take Off (PTO)
- 2. GETTING ON AND OFF THE TRACTOR
- 3. STARTING THE TRACTOR
- 4. SETTING THE MOWER
- Roller Height Adjustment
- 1. Place the tractor and mower on a level surface and completely lower the mower to the ground.
- 2. Shut down the tractor, place the transmission in park, and set the parking brake before dismounting.
- 3. One section at a time, place lifting device (scissors jack or hydraulic jack) under center of cutter housing.
- 4. Remove hex nuts, washers and carriage bolts from bracket at each end of roller. Make certain that roller bracket is free to move once the fasteners are removed. A stuck roller could drop unexpectedly and cause injury.
- 5. Use lifting device to reposition cutter housing to desired cutting height. Align bracket holes with cutter housing, then reinstall hardware.
- 6. Lower cutter housing to the ground and remove lifting device.
- 7. Set cutting height according to procedures above for remaining two cutter sections. Make sure that all three rollers are set at the same height to ensure an even cut across the entire width of the mower.
- Leveling Deck
- Roller Height Adjustment
- 5. DRIVELINE ATTACHMENT
- 5.1 Driveline Length Check
- “Bottoming Out” Check Procedure”
- 1. Disconnect driveline from the tractor and slide the profiles together until fully compressed.
- 2. Place a mark on the inner shield 1/8” from the end of the outer shield and reattach the driveline to the PTO shaft.
- 3. With the PTO NOT TURNING, slowly drive the tractor with mower attached through the sharpest turn possible and watch shaft movement. With the PTO NOT TURNING, slowly drive the tractor with the mower attached through the most severe terrain conditio...
- 4. If the distance between the mark and the outer shield becomes less than 2” at any point there is a potential problem bottoming out the driveline and the driveline should be shortened.
- 1. Remove the driveline from the tractor.
- 2. Position the mower to the point with the shortest distance between the tractor PTO shaft and cutter gearbox. Shut down the tractor and securely block the mower in this position.
- 3. Pull driveline apart and reattach yoke to PTO shaft.
- 4. Hold driveline sections parallel to one another and measure back 1” from yoke of each shaft and place mark on opposite section. Cut this length off with a saw.
- 5. Round off all sharp edges and debar.
- 6. Thoroughly grease then reinstall the driveline.
- 7. Recheck for proper operation.
- 1. With the driveline attached, position the mower to the point where the telescoping driveline is at its maximum extension. Completely shut down the tractor and secure in position.
- 2. Mark the inner driveline shield 1/8” from the end of the outer shield.
- 3. Disconnect the driveline from the tractor and separate the two driveline halves.
- 4. Measure the distance from the mark to the end of the inner profile. This length is the amount the driveline profiles were engaged.
- 5. If the engaged length is less than 8”, the shaft is considered too short and should be replaced with a longer shaft. Consult an authorized dealer to purchase the required driveline length.
- “Bottoming Out” Check Procedure”
- 5.1 Driveline Length Check
- 6. PRE-OPERATION INSPECTION AND SERVICE
- 7. DRIVING THE TRACTOR AND IMPLEMENT
- 8. OPERATING THE TRACTOR AND IMPLEMENT
- 8.2 Bystander/Passersby Precautions
- 11. MOWER STORAGE
- 1. Thoroughly clean all debris off the mower to prevent damage from rotting grass and standing water.
- 2. Lubricate all mower grease points and fill hydraulic tank oil level as detailed in the maintenance section.
- 3. Tighten all bolts and pins to the recommended torque.
- 4. Check the mower for worn and damaged parts. Perform repairs and make replacements immediately so that the mower will be ready for use at the start of the next season.
- 5. Store the mower in a clean, dry place with the mower housing resting securely on blocks or at ground level.
- 6. Keep the driveline yoke from sitting in water, dirt and other contaminants.
- 7. Use spray touch-up enamel where necessary to prevent rust and maintain the appearance of the mower.
- 12. TRANSPORTING THE TRACTOR AND IMPLEMENT
- 13. TROUBLESHOOTING GUIDE
- DAILY CHECKS
- 1. Lubricate the VERSA PRO at the specified intervals as outlined in the lubrication diagram. All mower grease fittings are equipped with lubricaps which snap over the grease fittings to prevent dirt from entering the fittings. Remove the cap and wip...
- 2. Before each day's use, follow this procedure:
- LUBRICATION INFORMATION
- CHANGING HYDRAULIC SYSTEM FILTER
- 1. Clean the filter cover to prevent dirt from entering tank.
- 2. Loosen the four bolts on the filter cover. Mnt-FL-0004. Remove one bolt from the filter to aid in removing the filter cover. Mnt-FL-0005.
- 3. Push the filter cover down and slowly twist the filter cover off. Mnt-FL-0006.
- 4. Remove filter spring. Mnt-FL-0007.
- 5. Remove filter. Inspect material trapped by the filter. It can indicate parts wear in the system. Mnt-FL-0008.
- 6. Install the new filter.
- 7. Reinstall filter spring and filter cover. Replace the one bolt which had previously been removed. Tighten all bolts in an even manner. Mnt-FL-0079.
- GENERAL
- REPLACING CUTTER UNIT DRIVE BELTS
- 1. Place unit on ground or support securely.
- 2. Remove belt guard.
- 3. Remove idler arm spring.
- 4. Remove extension shaft housing mounting bracket front bolt and loosen rear bolt.
- 5. Remove motor mounting bracket front bolt and loosen rear bolt.
- 6. Pivot motor-mounting bracket assembly. Remove old belts and install new ones.
- 7. Reinstall front mounting bolt then secure motor mounting bracket to unit.
- 8. Reinstall idler arm spring and belt guard.
- ADJUSTING CUTTING HEIGHT
- 1. Lower cutter unit to ground.
- 2. Place lifting device (scissors jack, hydraulic jack) under center of cutter housing.
- 3. Remove hex nuts, washers and carriage bolts from bracket at each end of roller. Make certain that roller bracket is free to move once the fasteners are removed. A stuck roller could drop suddenly and cause an injury.
- 4. Use lifting device to reposition cutter housing to desired cutting height. Align bracket holes with cutterhousing holes, then reinstall fasteners.
- 5. Lower cutter unit to ground; then remove lifting device
- ROLLER BEARING REPLACEMENT
- 1. Remove roller and both bearing and bracket assemblies from mower. Lift the mower only high enough to remove the roller assembly.
- 2. Slide bearing and bracket assemblies off each end of roller.
- 3. Remove roller bearing and housing assembly attaching hardware. Remove assembly from bracket. Inspect seal between assembly and bracket for brittleness, cracks, wear and tear. Replace if necessary.
- 4. Remove grease fitting from the top of bearing housing.
- 5. Remove bearing from housing. By rotating Bearing 90 degree sideways and line up with notches in Bearing Housing; then pull out
- 6. Install new bearing into housing. Bearing must be installed with grease hole in bearing aligned with grease fitting hole in housing.
- 7. Reinstall grease fitting to housing. Grease fitting must be tight and seated in grease hole in bearing to prevent bearing from rotating in housing.
- 8. Attach roller bearing and housing assembly to bracket with seal between housing and bracket.
- 9. Slide bearing and bracket assemblies on each end of roller.
- 10. Check bearing for proper installation in housing by gently rocking bearing and bracket assembly in end of roller. Play should be slight to none at all.
- 11. Install roller and bearing and bracket assemblies on mower.
- 12. Lubricate roller bearing until lubricant can be seen coming out between roller and bearing housing.
- CUTTERSHAFT BEARING REPLACEMENT
- 1. Lift cutter unit to maximum horizontal height; then securely support ends of cutterhousing.
- 2. Remove enough knives to place a floor jack under center of cutterhousing.
- 3. Securely support cuttershaft.
- 4. Remove outboard fender.
- 5. Remove fasteners securing bearing and housing assembly to cutterhousing, then remove bearing and housing assembly.
- 6. Using a jack to align parts, install bearing and housing assembly to cutter unit and make certain that bearing setscrew is located in keyway on cuttershaft. Grease bearing and install cap over fitting.
- 7. Remove Belt Guard.
- 8. Remove spring from idler arm.
- 9. Remove motor mounting bracket fasteners, at the cutterhousing. Pivot motor-mounting bracket assembly and remove drive belts.
- 10. Remove fasteners that secure pulley to cuttershaft. Remove pulley and key.
- 11. Remove fasteners securing inboard bearing and housing assembly to cutterhousing, then remove bearing and housing assembly. Refer to Illustration 11.
- 12. Using a jack to align parts, install inboard bearing and housing assembly to cutter unit. Grease bearing and install cap over fitting.
- 13. Reinstall key and pulley. Secure with cuttershaft fasteners.
- 14. Remove jack and check shaft rotation. Reinstall knives which were removed.
- 15. Reinstall drive belts then secure motor mounting bracket to cutterhousing.
- 16. Reinstall idler arm spring.
- 17. Reinstall belt guard.
- 18. Remove supports, lower unit to ground and test unit. Reinstall outboard fender, if not already installed.
- CUTTERSHAFT REPLACEMENT
- 1. Place unit on the ground or securely support at a convenient height.
- 2. Remove cuttershaft bearing and cutter assemblies as outlined in above. After removing both assemblies, the cuttershaft can be removed and a new one installed. It may be necessary to remove two sets of knives nearest the drive end of cuttershaft.
- 3. Install new bearing and housing assemblies as outlined in Image Mnt-FL-0063.
- Changing to Forward or Reverse Rotation
- Replacing Cutter Unit Knives
- HYDRAULICS
- GENERAL
- INITIAL START-UP PROCEDURES
- 1. Check all nuts and bolts to be sure they are tight and that all lock washers are fully compressed.
- 2. Check all hoses and hydraulic connections to be sure that they are tight.
- 3. Inspect all moving parts, and make certain that no wires or hoses will be caught or pinched when the tractor is in operation.
- 4. Thoroughly lubricate the VERSA PRO. Refer to Mnt-FL-0077, Section 5-3.
- 5. Change the hydraulic filter and fill the reservoir to the sight glass with new hydraulic oil. Refer to 2-5 for specifications.
- 6. Turn mowers off, then start tractor and run engine at low idle. Operate the cylinder, (turn cutter units on ONLY when mowers are fully lowered). Operate until the system is fully charged. Recheck the fluid level and add oil, if necessary. If undue...
- 7. After the hydraulic system is fully charged and functioning properly, switch the mowers on and increase the engine speed to run the 540 PTO speed. Maintain this speed for 5 minutes and look for any leaks or possible problems.
- HYDRAULIC PUMPS
- REPLACING HYDRAULIC PUMPS
- 1. Remove the Pump Cover by unscrewing the wing nut which holds it in place.
- 2. Disconnect the outer Pump Suction Hose, Case Drain Hose, and the Pressure Hose.
- 3. Remove the two bolts which attach the outer pump to the inner pump flange.
- 4. Remove Pump. Lightly oil new "O" Ring and place on inner pump flange. Install the new Pump with the pump drain ports facing Hydraulic Tank.
- 5. Reinstall hydraulic hoses. Tighten hose fittings to their proper torque. Refer to Torque Chart.
- 6. Reinstall Pump Cover and tighten the four thumb screws securely.
- 7. To replace inner pump both pumps must be removed. Follow same procedure as for outer pump. BE SURE TO CAP ALL HOSES AND CLEAN OIL SPILLS AT ONCE.
- 8. Separate the inner pump from the outer pump and install new pump to inner pump following step 4 making sure both case drain ports are facing hydraulic reservoir.
- 9. Reinstall pumps to pump mounting bracket.
- 10. Reinstall all hoses. Tighten hose fittings to their proper torque refer to torque chart.
- 11. Reinstall all guards.
- RESERVOIR
- SOLENOID CONTROL VALVE
- HYDRAULIC
- DISASSEMBLY
- 1. Disconnect all hydraulic lines. Remove pump assembly from tractor.
- 2. Plug all ports and thoroughly clean outside of pump.
- 3. Clamp the end of the drive shaft in a protected jaw vise with the body of the pump up and remove the six cap screws from the back plate.
- 4. Use a plastic mallet and tap the back plate assembly to loosen it, then pull back plate straight up until it is free. Remove gasket.
- 5. Remove pump from vise and remove rotating assembly from pump housing.
- 6. If the pistons did not come out with the piston block, remove them, the spider, and the spider pivot.
- 7. The piston block assembly need not be disassembled unless the internal pins of spring is damaged.
- 8. Remove snap ring from housing. Press shaft from housing and remove shaft seal and washer.
- 9. Remove the two snap rings, thrust bearing, and two thrust washers from the drive shaft.
- 10. To remove the cam plate from housing, remove the four screws from sides of the housing. Remove trunnion cover, seal cover, and o-ring cover. Remove o-ring, seal, two washers, inner race, and needle bearings. The cam plate can now be moved over to...
- DISASSEMBLY
- INSPECTION
- 1. Inspect flat surface of the backplate. The finish on the piston block side should be smooth and free of grooves. DO NOT LAP BACKPLATE WEAR SURFACE. The backplate should be replaced if it shows any of the wear characteristics outlined above. Inspec...
- 2. Inspect the piston block. The wear surface that contacts the backplate should be smooth and free of grooves. DO NOT LAP PISTON BLOCK.
- 3. The pistons should move freely in the piston block bores. If they are sticky in the bore, examine the bore for scoring or contamination.
- 4. Examine the O.D. of the pistons for finish condition. They should not show wear or deep scratches. The shoes should be a snug fit on the ball end of the pistons. The flat surfaces of the shoes should be flat and smooth. DO NOT LAP THE PISTON SHOES.
- 5. Examine the spider. It should be flat, no cracks and no signs of wear in the pivot area.
- 6. Examine the pivot. It should be smooth and show no signs of wear.
- 7. The cam plate should be inspected for the condition of the finish of the polished shoe surface. It should show no signs of scoring. Inspect the camplate pivot bearings. If the needles are free of excessive play and remain in the bearing cage, ther...
- 8. Inspect the drive shaft for fretting in the bearing and spline areas.
- 9. Inspect the thrust bearing and thrust washers for wear.
- 10. Inspect the needle bearing in the housing. If the needles are free of excessive play and remain in the bearing cage, there is no need to replace the bearing.
- REASSEMBLY
- 1. Clean all parts in a suitable solvent. Lubricate all critical moving parts before reassembly. If necessary, install new needle bearing in housing with numbered end of bearing outward.
- 2. Insert cam plate into housing. Insert needle bearings and inner race. The chamfered I.D. of the race should be inward. Install washers, o-ring seal, o-ring cove, trunnion cover, seal cover, and retain with four screws and tighten to 36-48 in. lbs.
- 3. Install snap ring on shaft. Install thrust washer, thrust bearing, and second thrust washer. Secure with second snap ring.
- 4. Install shaft in housing and install washer and shaft seal and retain with snap ring.
- 5. Compress pin keeper and install in the spline of the piston block. Install the three pins with head end to the inside of the block, and install in the special grooves of the piston block spline.
- 6. Install washer, spring, and second washer in the piston block. Use the two 3/8 I.D. washers and the 3/ 8 x 3-1/4 cap screw to compress the spring and retain with snap ring. Remove the 3/8 x 3-1/4 cap screw and the two washers.
- 7. Install the pivot, spider, and the piston assemblies in the piston block. Install this assembly in the housing assembly. The piston shoes must be in contact with the cam plate. Be sure all the parts are in their proper position.
- 8. Clamp this assembly in a protected jaw vise with the open end of the housing up.
- 9. Install new gasket.
- 10. Install relief valves and springs into backplate.
- 11. Install backplate assembly. Install sixcap screws and torque to 27-31 ft. lbs.
- HYDRAULIC MOTOR
- DISASSEMBLY
- 1. Clean outside of unit thoroughly. Refer to Hydraulic Motor illustration in the Parts Listing section.
- 2. Clamp shaft in a protected jaw vise with backplate end up.
- 3. Remove six bolts from backplate.
- 4. Use a plastic mallet and tap the backplate to loosen it.
- 5. Remove o-ring from backplate.
- 6. Remove the complete piston block assembly from the housing assembly.
- 7. Remove piston assemblies, spider, and pivot form piston block assembly.
- 8. The piston block assembly need not be disassembled unless the pins or spring is damaged.
- 9. Remove thrust race from housing.
- 10. Remove snap ring from housing.
- 11. Remove shaft seal from housing.
- 12. Remove washer from housing.
- 13. Remove drive shaft from housing.
- 14. Remove the two snap rings, thrust washers, and thrust bearing, from drive shaft.
- DISASSEMBLY
- INSPECTION
- 1. Wash all parts thoroughly in a suitable solvent.
- 2. Examine needle bearings in housing and backplate.
- 3. Inspect thrust washers and thrust bearing. All surfaces should be free of any signs of wear or fretting.
- 4. Inspect spider and pivot; conical surfaces should be free of wear and score marks.
- 5. Inspect the pistons: the O.D. surface should be smooth and free of scoring. The shoes should be snug fit to the piston. The face of the shoes should be flat and free of scoring and flaking. DO NOT LAP PISTON SHOES.
- 6. Inspect the piston block; the bores should be free of scoring. The surface that contacts the backplate should be smooth and free of grooves or metal build-up. Do not lap piston block.
- 7. Inspect the thrust race; the surface should show no signs of scoring or grooves.
- 8. Inspect the flat surface on the backplate; it should be free of excessive scoring or metal build-up. DO NOT LAP BACKPLATE.
- 9. Inspect the drive shaft for fretting in the bearing areas. Check spline area for twisted or broken teeth. If keyed shaft, check for cracked or chipped keyway.
- REASSEMBLY
- 1. Use filtered system oil to lubricate all critical moving parts before assembly.
- 2. Install one snap ring in rear groove of drive shaft. Install one thrust washer, thrust bearing, and second thrust washer on drive shaft. Install second snap ring in front groove on drive shaft.
- 3. Replace needle bearing in housing if necessary. Install shaft in housing assembly and install washer. Oil O.D. of new shaft seal and press into position. Retain with snap ring.
- 4. Compress pin keeper and install in the spline area of the piston block.
- 5. Install the three pins in the special grooves of the spline and with head end of pin toward inside of bock.
- 6. Install one washer, spring, and second washer. Use the two 3/8 I.D. washers and the 3/8 x 3-1/4 capscew to compress the spring and retain with snap ring. Remove the 3/8 x 3-1/4 capscrew and two washers.
- 7. Install the pivot, spider, and the piston assemblies in the piston block assembly.
- 8. Lubricate thrust race and install in housing assembly.
- 9. Install piston block assembly in housing assembly. The piston shoes must contact the thrust race. Be sure all parts are in their proper position.
- 10. Install new needle bearing in backplate if necessary.
- 11. Install new o-ring on backplate.
- 12. Install backplate on housing.
- 13. Install six capscrews and torque 15-18 ft. lbs.
- 14. On through shaft type assembly, install shaft seal and snap ring in backplate. Install key in drive shaft.
- LIFT CYLINDERS
- DISASSEMBLY OF LIFT CYLINDER
- 1. Disconnect hoses at cylinder. Cap all hoses to prevent fluid contamination. Remove cylinder from unit.
- 2. Remove reducer bushing and snap ring which retains the rod guide. Remove rod guide, rod, and piston. Remove guide and piston from rod.
- 3. Replace all "O" rings, back-up washers, and rod wiper. Inspect rod, guide, piston, and body for damage.
- 4. Clean inside of cylinder with mineral spirits. DO NOT wipe dry; air dry instead. Lint, dirt, and, grit can cause immediate or premature failure.
- 5. Lubricate all parts with clean hydraulic oil and reassemble.
- 6. Reinstall cylinder with stop located on the upper side, to prevent bending the rod.
- DISASSEMBLY OF LIFT CYLINDER
- EXTERNAL COIL SLIP CLUTCH DISK REPLACEMENT
- TO DISASSEMBLE EXTERNAL COIL SPRING CLUTCH
- 1. Remove two Attaching Bolts (6). Remove Clutch Assembly from shaft of Gearbox. Leave Driveline or Driveline Half attached to Clutch.
- 2. Loosen six Adjusting Bolts (1). LOOSEN EACH BOLT A FEW TURNS AT A TIME - NOT ALL AT ONCE. Continue in rotation until Nuts are loose. Remove these Bolts. Flange Yoke (9) will slide off. On Clutches that have Dust Shields (11), Shields will slide of...
- 3. On the opposite side, Outer Flange (2) will slide off which will allow Clutch Plate (3) to slide over notches on outside diameter of Clutch Body (5).
- 4. Remove Plate with six bolt holes (7).
- 5. Remove the four Friction Disks (4) and discard. DO NO RE-USE.
- TO CLEAN AND INSPECT
- TO REASSEMBLE
- TO ADJUST
- TO REPLACE SHIELDS
- TO TEST FOR FROZEN CLUTCHES
- TO DISASSEMBLE EXTERNAL COIL SPRING CLUTCH
- VERSA PRO TANK FILLING INSTRUCTIONS
- STORAGE
- TO THE OWNER/OPERATOR/DEALER
- ALAMO-INDUSTRIAL
- LIMITED WARRANTY
- 1. LIMITED WARRANTIES
- 1.01. Alamo Industrial warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser
- 1.02. Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship.
- 1.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, ...
- 1.04. Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer.
- 2. REMEDIES AND PROCEDURES.
- 2.01. This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase.
- 2.02. Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based
- 2.03. Purchaser is responsible for returning the goods in question to the Dealer.
- 2.04. If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will:
- (a) Repair or replace the defective goods or part(s) or
- (b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer.
- 2.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for...
- 3. LIMITATION OF LIABILITY.
- 3.01. MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
- 3.02. MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS.
- 3.03. EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLU...
- 3.04. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.
- 4. MISCELLANEOUS.
- 4.01. Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas.
- 4.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term.
- 4.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein.
- 4.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.