Alamo 800 User Manual
Operator’s manual, Rear mounted blade
© 2011 Alamo Group Inc.
$0.00
800
Published 01/11
Part No.
00762259C
OPERATOR’S MANUAL
RHINO
®
1020 S. Sangamon Ave.
Gibson City, IL 60936
800-446-5158
Email: [email protected]
REAR MOUNTED BLADE
This Operator's Manual is an integral part of the safe operation of this machine and must
be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety
and Operation Instructions contained in this manual before operating the equipment. C01-
Cover
Table of contents
Document Outline
- 800
- OPERATOR’S MANUAL
- To the Owner/Operator/Dealer
- TABLE OF CONTENTS
- Safety Messages
- Decal Location
- 1. 00725746 1 PELIGRO Translate Safety Material
- 2. 00760657 1 IMPORTANT Genuine Rhino Parts
- 3. 999000 1 WARNING Multi-Hazard, Blades
- 4. 999200 1 WARNING Multi-Hazard, General
- 5. 000678 1 INSTRUCT Grease Fitting Inside
- 6. 00763977 1 INSTRUCT Notice to Owner
- 7. D303 3 LOGO Rhino (4-3/8 x 16-3/4)
- 8. 00762256 1 NAME 800 Blade
- 9. nfs 1 SERIAL PLT Serial Plate 800
- 10. 03200347 * REFLECT SMV Emblem
- 11. 1458392 2 REFLECT Red Reflector (7’ & 8’)
- 12. 1458393 1 REFLECT Amber Reflector (8’)
- 13. 00785885 1 LOGO 7 FT
- 14. 00776031 1 _________ Canister
- 15. 00762259C 1 _________ 800 RB Operators Manual
- Decal Description
- 1. Standard Equipment and Specifications
- 3. TRACTOR REQUIREMENTS
- Tractor Requirements and Capabilities
- 3.1 ROPS and Seat Belt
- 3.2 Tractor Horsepower
- 3.3 Tractor 3-Point Hitch
- 3.4 Front End Weight
- 4. GETTING ON AND OFF THE TRACTOR
- 5. STARTING THE TRACTOR
- 6. CONNECTING THE REAR BLADE TO THE TRACTOR
- 6.1 Connecting the Rear Blade
- 1. Shorten or remove the tractor drawbar to avoid interference when raising and lowering the rear blade.
- 2. Board the tractor and start the engine. Position the tractor to the blade with the 3- point lift arms positioned between the respective set of blade A-frame lift lugs. Note: Set the 3-point lift control to “Position Control” so that the lift a...
- 3. Turn off the tractor engine, set the parking brake, place the tractor in park, and dismount.
- 4. One lift arm at a time, align arm end hole between the set of holes of A-frame lift lugs. Insert hitch pin through the lug and arm holes and insert retaining pin into hitch pin. Walk around to opposite side and repeat procedure for remaining lift ...
- 5. Extend or retract the 3-point top link to align its end hole with the holes of the blade’s top link. Insert the top link bolt and retain with top lock nut.
- 6. Adjust any lower link check chains, guide blocks, or sway blocks to prevent the blade from swaying side to side and possible contact with tractor rear tires.
- 6.1 Connecting the Rear Blade
- 7. PRE-OPERATION INSPECTION AND SERVICE
- 8. DRIVING THE TRACTOR AND IMPLEMENT
- 9. OPERATING THE TRACTOR AND IMPLEMENT
- 10. BLADE AND TRACTOR PREPARATION
- 14. TROUBLESHOOTING GUIDE
- Bent Moldboard Small curve is normal from weld Can be removed but will not affect
- pull operation
- Hitting hidden objects Know soil conditions, keep speed to
- a minimum.
- Blade will not penetrate soil Cutting edge dull Replace Cutting edge
- Blade set to straight Increase Top Link length
- Soil too hard Use scarifiers to loosen soil
- A-Frame bent Hitting hidden objects in the Use slow speed when in unknown
- backfill position soil conditions
- Moldboard digging in too Blade pitch excessive Adjust Top Link
- much Soft ground Install Planer Wheel
- Install Skid Shoes
- Unable to hold level ground Tractor and Blade following contour Install Planer Wheel
- Tractor Draft Control lifting Blade Set Tractor Draft Control
- Shearing Index Pins Hitting Solid Objects Know Soil Conditions
- Carrier Index Pin Worn Replace Worn Parts
- Carrier Index Pin Soft Replace Pin
- OPERATION SECTION
- MAINTENANCE SECTION
- Proper Torque For Fasteners
- RHINO
- LIMITED WARRANTY
- 1. LIMITED WARRANTIES
- 1.01. Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the ...
- 1.02. Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship.
- 1.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, ...
- 1.04. Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer.
- 2. REMEDIES AND PROCEDURES.
- 2.01. This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase.
- 2.02. Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based
- 2.03. Purchaser is responsible for returning the goods in question to the Dealer.
- 2.04. If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will:
- (a) Repair or replace the defective goods or part(s) or
- (b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer.
- 2.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for...
- 3. LIMITATION OF LIABILITY.
- 3.01. MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
- 3.02. MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS.
- 3.03. EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLU...
- 3.04. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.
- 4. MISCELLANEOUS.
- 4.01. Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas.
- 4.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term.
- 4.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein.
- 4.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.
- LIMITED WARRANTY
- TO THE OWNER/OPERATOR/DEALER