American Standard Williamsburg 2806E - Manual

INSTALLATION INSTRUCTIONS
752872-100 REV. C
© American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
WILLIAMSBURG
ELITE™ 6'
WHIRLPOOL
2806E SERIES
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
T H A N K Y O U . . .
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately.
After inspection and during installation, protect the bath from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit and check for leaks.
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,
motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead
(required for recess installations).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
List of Optional Components (not included):
• Flex-Jet Pulse Jet Kit*
• Flex-Jet Soft Jet Kit*
• E-Z-Install Heater*
List of Required Components (not included):
• Drain* • Bath Filler*
* see your Home Depot Retailer
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 20 amp GFI
Outlet
• Cement, Plaster,
Grout
GENERAL SPECIFICATIONS FOR 2806E WHIRLPOOL
72 x 36 x 21-1/2 In. (1829 x 914 x 546mm)
135 Lbs. (61 Kg.)
744 Lbs. (338 Kg.)
73 Gal. (276 L)
44 Gal. (167 L)
45 x 24 In. (1143 x 610mm)
60 x 30 In. (1524 x 762 mm)
14-1/2 In. (368mm)
41 Lbs./Sq.Ft. (198 Kgs./Sq.m)
25.6
49.4
2.1 HP, 14.4 AMPS ,120V. PUMP
WHIRLPOOL ELECTRICAL SPECIFICATIONS
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3 )
914mm
(36)
457mm
(18)
279mm
(11)
INTEGRAL
FITTING DECK
ON/OFF
SWITCH
1829mm
(72)
PUMP
140mm
(5-1/2) C/L OF
DRAIN
OVERFLOW
OUTLINE OF
CUTOUT
229 x 330mm
(9 X 13)
FLOOR
CUTOUT
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
LEVELING STRINGER
(NOT FOR SUPPORT)
1-1/2 N.P.T.M. THREADS
51mm
(2)
108mm
(4-1/4)
546mm
(21-1/2)
495mm
(19-1/2)
ROUGH
FLOOR
INTEGRAL
FEET
SUPPORT
1-1/2 O.D.TAILPIECE
51mm
(2)
108mm
(4-1/4)
IN-LINE HEATER
REMOVABLE
BLANK
C/L OF
OVERFLOW