Ultra Start 600 - Manual (Page 9)

Installation Guide
PROGRAMMING
9
PROGRAM MODE - ALARM SETTINGS
Setting 1 - Car Finder/ 5th Channel
Setting 2 - Secure Valet Mode
Setting 3 - Park Light Output
Setting 4 - Horn Honk Timing
Setting 5 - 4th Channel Settings
Setting 6 - Car Jack Mode
Setting 7 - Horn/ 5th Channel
Enter Alarm Program Mode - See Page 7. for details on entering Program Mode
1 Car Finder OFF 1 Light Flash Car Finder Mode Disabled
*2 Car Finder ON 2 Light Flashes Car Finder Mode Enabled
Note: To operate the 5th channel on button #4, setting 7 must be programmed for 5th channel output.
1 30 Second Parking Lights on Disarm 1 Flash Park Lights on for 30 seconds on disarm
2 Negative Park Light 2 Flashes Switches the Park Light and the Trunk Release (3rd Channel) Outputs
3* Normal Parking Lights 3 Flashes 2 Park Light Flashes on disarm
1 5ms 1 Flash Short (Quiet) Pulses
2 20ms 2 Flashes Long (Loud) Pulses
*3 10ms 3 Flashes Normal (Medium) Pulses
1 Secure Valet Active 1 Flash Valet only if ignition “ON” and valet switch held for 15 seconds
2* Normal Valet Active 2 Flashes Valet if ignition “ON” and valet switch held for 5 seconds
Press the Valet Switch 1 time to select setting 1 (This will be confirmed by 1 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
1 Pulsed 1 Flash Pulsed for 0.75 seconds upon 4th Channel Activation
2 Latched 2 Flashes Latched until repeated or ignition “ON”
*3 Active 3 Flashes Active for as long as the button is held on Transmitter.
1 Door & Button 1 Flash Activated upon Button 4 or Door open while Ignition is “ON”
2 Door, Button 4 2 Flashes Activated upon Button 4 or Door open or ignition “ON” and Ignition
*3 Car Jack OFF 3 Flashes No Car Jack Functions
1 5th Channel 1 Flash Pulsed output when activated by button #4
2 Horn Honk 2 2 Flashes Horn Honk Output - Full Alarm ONLY
*3 Horn Honk 1 3 Flashes Horn Honk with Arm & Disarm Chirps
Press the Valet Switch 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the lock and Star buttons together to activate the 4th Channel output.
The Shock Sensor and ignition will be bypassed upon 4th channel activation.