Warren Controls 3800 Series E-BALL ROTARY CONTROL VALVES - Manual (Page 2)

2 2600 Emrick Blvd • Bethlehem, PA 18020 • USA • 800-922-0085 • www.warrencontrols.com 3800_IOM_RevB_0513
thoroughly reviewed to determine the proper integration of the
equipment into the overall plant operational procedures. Warren
Controls does not assume responsibility for the selection, use, or maintenance of any product. Responsibility for proper selection,
use, and maintenance of any Warren Controls product remains solely
with the purchaser and end-user.
To use these instructions it is necessary to identify the configuration
of the valve. Factory assembled control valves with a pneumatic or
electric actuator have a serial number label attached to the actua-
tor. The valve’s part number (P/N) is present on the label. The part
number represents the configuration of the control valve. To identify
the valve’s type, size, actuator, accessories, and other characteristics decode the part number using the configuration table in the Series
3800 Product Specification. If the information is incomplete, incor-
rect, or not present contact the factory with the valve serial number.
(See Information Present on Control Valves or Information Present
on Bare Stem Valves section for location of important information
on valves.)
gENERAL INFORMATION (Continued)
Series 3800 E-Ball Rotary Control Valves are available with a variety
of actuators and accessories. These actuators and accessories
have separate instructions. For complete control valve installation, operation, and maintenance instructions see also the instructions
for the actuator and accessories in use.
ACTUATORS AND ACCESSORIES
VALVE IDENTIFICATION
385
1” - 2” Bodies
(EN ISO 5211-F07-N-L-11*)
386
3” Bodies
(EN ISO 5211-F07-N-L-14*)
387
4” Bodies
(EN ISO 5211-F07/F10-N-L-17*)
388
6” or 8” Bodies
(EN ISO 5211-F10-N-L-22*)
389
6” or 8” Bodies
(EN ISO 5211-F12-N-L-22*)
* ISO 5211-2001
Designations
Size
Body
Material
End
Connection
Shaft
Material
100
1 inch
150
1-1/2
inch
200
2 inch
300
3 inch
400
4 inch
600
6 inch
800
8 inch
W
WCB
F
CF8M
Trim Cv
F
Full Port
1
1st Port
Reduction
2
2nd Port
Reduction
3
3rd Port
Reduction
Shaft
Design
C
Thru, Direct
D
Thru, Indir.
E
Split, Direct
F
Split, Indir.
F
150 lb.
Flanged
G
300 lb.
Flanged
Trim Material
S
316 Stainless Stl.
T
TFE Soft Seats
P
PEEK Soft Seats
6
Alloy 6
H
Alloy 6 Hard
Seat
Z
TTZ Ceramic
316 SS Seat
R
TTZ Ceramic
17-4PH Hard
Seat
Y
Y-TZP Ceramic
(Ceramic Seat,
Sleeve & Plug)
S
17-4 Hard
I
Inconel
Model
Packing
Bearing &
Seals
VALVE BODY
T
Teflon V-ring
Self Adjusting
G
Adjustable
Graphite Indir
Mtg & Alloy 6
Brngs
J
Adjustable
Graphite Indir
Mtg & PEEK
Brngs
A
Adjustable
Teflon
V-ring Indir
Mtg
S
PEEK
6
Alloy 6
T
PEEK
w/Fluoraz
Seal
Y
Alloy 6
w/Fluoraz
Seal
ST PEEK Brngs; Self-Adj Teflon
Pkg To 450F
SJ PEEK Brngs; Adj Graphite Pkg
(Requires Indir Shaft) To 450F
SA PEEK Brngs; Adj Teflon Pkg
(Requires Indir Shaft) To 450F
6G Alloy 6 Brngs; Adj Graphite Pkg
(Requires Indir Shaft) To 800F
TT PEEK Brngs w/ Fluoraz Seal;
Self-Adj Teflon Pkg To 450F
TJ PEEK Brngs w/ Fluoraz Seal;
Adjustable
Graphite Packing (Requires
Indir Shaft) To 450F
TA PEEK Brngs w/ Fluoraz Seal;
AdjTeflon Pkg
(Requires Indir Shaft) To 450F
YG Alloy 6 Brngs w/ Fluoraz Seal;
Adj Graphite Pkg
(Requires Indir Shaft) To 500F
SG, 6J, 6T, 6A, TG, YT, YJ, YA
Not Available
ACTUATOR / VALVE COMPATIBILITY:
PNEUMATIC
RACK & PINION
VALVE
MODEL
VALVE
SIZE
073 Size RP73
385 1” - 2”
386 3”
103 Size RP103
385 1” - 2”
386 3”
148 Size RP148
385 1” - 2”
386 3”
387 4”
388 6” & 8”
222 Size RP222
385 1” - 2”
386 3”
387 4”
388 6” & 8”
295 Size RP295
385 1” - 2”
386 3”
387 4”
388 6” & 8”
470 Size RP470
387 4”
388 6” & 8”
586 Size RP586
387 4”
388 6” & 8”
900 Size RP900 389 6” & 8”
999 Size RP1213 389 6” & 8”
ELECTRIC
120VAC
VALVE
MODEL
VALVE
SIZE
EA3 Size P2 385 1” - 2”
386 3”
387 4”
EB3 Size P3 385 1-1/2” - 2”
386 3”
387 4”
E04 Size P4 387 4”
388 6” & 8”
E05 Size P5 387 4”
388 6” & 8”
E06 Size P6 388 6” & 8”
E07 Size P7 389 8”