KYORITSU KEW Windows for KEW 3128 Windows 8 - Manual

Driver Installation Manual for "KEW Windows for KEW3128"
This manual contains explanations how to install the special
application and the USB driver on Windows 8 PCs.
1. Installation of KEW Windows for KEW3128
(1) The following should be checked before installing this
application.
･ To prepare your system for installation, please close
all open programs.
･ Be sure NOT to connect the instrument with the USB
until installation completes.
･ Installation shall be done with Administrator right.
･ To use KEW Windows for KEW3128, .NET Framework
3.5 is required.
If .NET Framework 3.5 is not installed in your PC, it
will be automatically installed when installing this
application.
An internet connection is required to install .NET
Framework 3.5.
(2) Insert the CD-ROM in your PC's CD drive. Then
following pop-up will appear at the upper right on the
screen. Left-click on this box.
(3) Click and select "Run KEWLauncher.exe" when the
following box appears.
If User Account Control dialog box appears, click "Yes".
If neither (2) nor (3) appears, run "KEWLauncher.exe"
from the CD.
(7) Confirm the information on installation, and then click"
Install" to start an installation.
The following box will appear if .NET Framework3.5 is
not installed in your PC.
If a message requiring restarting your PC is displayed,
click "Yes" and restart your PC.
Run "KEWSetupLauncher.exe" from the CD after
restarting the PC.
(11) Click "Next" after entering the user information and
other supplementary information.
(12) Confirm the information on installation, and then click"
Install" to start an installation.
(13) Click "Finish" when "InstallShield Wizard Complete"
dialog box appears.
2. Installation of USB Driver
(1) Connect MODEL8212 and your PC with the USB cable
supplied with the instrument.
When the following window appears, install the driver
according to the following procedure.
(2) Click "Control Panel" -> "Device Manager".
(3) Click“O ther devices”and then right- click on
“ MODEL8212”.
Then click“Update Driver Software”.
(4) Select “Browse my computer for driver software".
(5) Check the box for“Include subfolders”, and then
click“Browse”.
(6) Select the disk drive in which the CD resides and click
OK.
If the CD is not inserted, close the window once by
clicking "Cancel" and select again after inserting the CD.
(7) When the following confirmation message appears,
after clicking“Next”, click“Install”.
Select "Install this driver software anyway" if the
following warning window appears. (There is no problem
to continue installing because operation has already
been verified.)
(8) Install is completed when the wizard says "Windows has
successfully updated your driver software".
Click "Close".
(8) Click "Finish" when "InstallShield Wizard Complete"
dialog box appears.
(9) When the installation wizard completes, subsequent
installation initiates automatically.
Click "Next".
(10) Read through and understand the License Agreement
and click I accept…., and then click" Next".
(9) Click“Other devices”under the Device Manager, and
then right-click on“USB Serial Port”.
Then click“Update Driver Software”.
(10) Repeat above step (3) through (6). Installation is
completed when the wizard says“Windows has
successfully updated your driver software”. Click
“ Close”.
(11) The following two icons will appear in the Device
Manager when the driver is successfully installed.
(4) When the following window appears, click "Next".
(5) Read through and understand the License Agreement
and click "I accept….", and then click" Next".
(6) Click "Next" after entering the user information and
other supplementary information.
USB Driver Un-installation
When the installation of the USB driver is interrupted and
re-installation cannot be done, follow the
procedure below and delete the existing driver, and then
install it again.
(1) Connect your PC and the instrument with the USB cord.
(2) Click the“Control Panel”in the Start menu.
(3) Click“Device Manager”in the Control panel.
(4) Right click on“MODEL8212 USB”under"Other devices".
(5) Click“Uninstall”to uninstall the USB driver.
(6) Remove the USB cord connecting your PC and the
instrument once, and connect them again.
(7) When“Found New Hardware Wizard”window appears,
follow the procedures described in“USB Driver
Installation”and install the driver.
92-2203