beautypg.com

KROHNE ALTOSONIC III EN User Manual

Page 16

background image

ALTOSONIC

III

16


Key

Measuring mode

Menu mode

Data level

Go to the parameter setting mode, function 1.00.00
OPERATION. If access CODE 1 is activated, CODE 1 must be
entered first. Using function 3.07.02 access CODE 1 can be
activated or deactivated.

Go to the next, lower menu level. Go to the next character or change line

(only when 2 lines are displayed)

Go to the error/Totalizer reset mode (via "CODE 2")

Return to the previous (higher)
menu level or leave the menu
mode.

Accept entered value

Cycle through measured values, see Function 3.03.07 CYCL
DISP

Cycle through menu options
within actual menu level.

Cycle active digit up to new values

Function

Text

Description and settings

0.00.00 ERROR/TOT

Main

menu

0.00.00

0.00.01

VIEW ERR

View error messages list

0.00.02

RST ERR

Reset error messages

0.00.03

UP2 SW NO

Software version micro processor 2

0.00.04

DSP SW NO

Software version digital signal processor

0.00.05

DISPLAY

Display test, all display items on

0.00.06

EXIT

Leave menu 0.00

1.00.00

OPERATION

Main menu 1.00.00 Operation

1.01.00 FLOW

Submenu

1.01.00

Flow

1.01.01

FULL SCALE

Full-scale value for 100% volume flow rate, see Function 3.01.01

1.01.02

ZERO VALUE

Zero value, see Function 3.01.02

1.01.03

ZERO CAL

Zero calibration, see Function 3.01.03

1.01.04

MASTER TC

Master time constant, see Function 3.01.04

1.01.05

LF CUTOFF

Low-flow cut-off, see Function 3.01.05

1.01.06

CUTOFF ON

Cut-off active, see Function 3.01.06

1.01.07

CUTOFF OFF

Cut-off de-active, see Function 3.01.07

1.02.00 DISPLAY

Submenu

1.02.00

Display

1.02.01

DISP FLOW

Display of flow, see Function 3.03.01

1.03.00

PULSE OUTP

Submenu 1.03.00 Pulse output

1.03.01

PULSE RATE

Pulse frequency value for 100% scale, see Function 3.05.08

1.03.02

PULSE/UNIT

Pulse value per volume flow unit, see Function 3.05.09

2.00.00

TEST

Main menu 2.00.00 Test functions

2.01.00 DISPLAY

Submenu

2.01.00

Display

2.01.01 DISPLAY

Test display, lights all pixels. End with

↵ key

2.02.00 OUTPUTS

Submenu

2.02.00

Outputs

2.02.01

CURRENT

Test current output
0 mA

4 mA

12 mA

20 mA

22 mA
Use up arrow to advance. Displayed value directly present at current output. Actual value present at
output after pressing

↵ key.

2.02.02

PULSE

Test pulse/frequency output
1 Hz

10 Hz

100 Hz 1000 Hz
2000 Hz
Use the up arrow to advance. Displayed value directly present at Pulse output. Actual value present at
output after pressing

↵ key

2.03.00 INPUTS

Submenu

2.03.00

Inputs

2.03.03

DIG INPUT

Test digital input
Measure level at digital input. End with

↵ key.

2.04.00

DEV INFO

Submenu 2.04.00 Device information

2.04.01 MANUFACT

Display

manufacturer

2.04.02

MODEL NO

Display model number

2.04.03

SERIAL NO

Display serial number

2.04.04

UP2 HW NO

Display µP2 hardware number

2.04.05

UP2 SW NO

Display µP2 software number

2.04.06

FRNT HW NO

Display front end hardware number

2.04.07

DSP HW NO

Display D.S.P. hardware number

2.04.08

DSP SW NO

Display D.S.P. software number

2.04.09

TIME COUNT

Display time counter

3.00.00

INSTALL

Main menu 3.00.00 Installation

3.01.00

FLOW

Submenu 3.01.00 Volume flow parameters