SANDPIPER Pail & Drum Transfer Kits - Manual (Page 4)

Page 2 520-188-000 6/03
WARREN RUPP, INC. • A Unit of IDEX Corporation • P.O. Box 1568, Mansfield, Ohio 44901-1568 • (419) 524-8388 • Fax (419) 522-7867 • www.warrenrupp.com
Pail Adaptor Kits 475-194-520 and
475-194-552 (Fits S05 and M05 pump models);
475-195-520 and 475-195-552
(Fits S07 and M07 pump models)
1. Remove the eight cap screws, the 16 flat washers and eight hex
nuts which fasten the suction elbows and suction manifold. Rotate
the suction manifold so the NPT port faces down. Re-install the
hardware.
2. Apply PTFE tape to the manifold NPT male threads to seal the
connection with the pipe assembly. Install the 595-007-520/
595-007-552 pipe assembly (for kit 475-194-xxx) or 595-008-520/
595-008-552 pipe assembly (for kit 475-195-xxx) to the NPT port
of the suction manifold.
3. Insert the pipe assembly through the large center hole in the
165-088-330 (for kit 475-194-xxx) or 165-089-330 (for kit
475-195-xxx) pail transfer cap provided with the conversion kit.
Using the hardware provided with the kit (four 170-032-115 hex
capscrews, four 545-003-115 hex nuts, and eight 901-035-115
flat washers), fasten the pump to the pail transfer cap.
4. The pump and cap assembly can now be fitted over the top of a
five-gallon pail. Tighten the three thumb screws on the Pail Transfer
Cap to secure the cap to the pail.
120# Barrel Adaptor Kits 475-196-520 and
475-196-555 (Fits S05 and M05 pump models)
1. Remove the eight cap screws, the 16 flat washers and eight hex
nuts which fasten the suction elbows and suction manifold. Rotate
the suction manifold so the NPT port faces down. Re-install the
hardware.
2. Apply PTFE tape to the manifold NPT male threads to seal the
connection with the pipe assembly. Install the 595-009-555 or
595-009-520 pipe assembly to the NPT port of the kit vertical
manifold.
3. Insert the piping assembly through the large center hole in the
165-103-000 barrel transfer cap provided with the conversion kit.
Using the hardware provided with the kit (four 170-032-115 hex
capscrews, four 545-003-115 hex nuts, and eight 901-035-115
flat washers), fasten the pump to the barrel transfer cap.
4. The pump and cap assembly can now be fitted over the top of a
120# barrel. Tighten the three thumbscrews on the barrel transfer
cap to secure the cap to the barrel.
55 Gallon Drum Adaptor Kit 031-091-520 and
031-091-555 (Fits S05 and M05 pump models)
1. Remove the eight cap screws, the 16 flat washers and eight hex nuts
which fasten the suction elbows and suction manifold to the outer
chambers.
Rotate the suction manifold 90°, so the threaded NPT port points down.
2. Re-install the hardware.
3. Apply PTFE tape to the manifold NPT male threads to seal the
connection with the pipe assembly. Install the 595-001-520 or
595-001-555 pipe assembly to the NPT port of the kit vertical
manifold.
4. Remove the larger bung plug from the drum and slowly lower the
pump and pipe into the barrel until the pipe bottoms out on the
drum. Snug the locknut.
5. Install the four (4) foot assemblies on the pump’s suction elbows,
using one nut and washer on both the top and bottom foot bracket.
Adjust the height of the foot assemblies, until the rubber portion of
the foot puts a slight amount of pressure on the drum. This will help
stabilize the pump.
6. Tighten the locknut on the pipe.
Pail Adaptor Kit
120# Barrel Kit
55 Gallon Drum Kit
for SandPIPER and MARATHON Kits