SANDPIPER M05 Non-Metallic - Manual (Page 3)

m05nmdl2sm-rev0114 Model M05 Non-Metallic Page 1
See page 2
for ATEX ratings. See pages 2, 32 and 33
for ATEX ratings.
Quality System
ISO9001 Certified
Environmental
Management System
ISO14001 Certified
InTake/DIsCharge PIPe sIze
1/2" NPT (Internal) or 1/2" BSP (Tapered)
1" NPT (External) or 1" BSP (Tapered)
CaPaCITy
0 to 14 gallons per minute
(0 to 52 liters per minute)
aIr ValVe
No-lube, no-stall design
solIDs-hanDlIng
Up to .125 in. (3mm)
heaDs UP To
100 psi or 231 ft. of water
(7 bar or 70 meters)
DIsPlaCemenT/sTroke
.026 Gallon / .098 liter
M05
Non-Metallic
Design Level 2
Ball Valve
Air-Operated
Double Diaphragm Pump
ENGINEERING, PERFORMANCE
& CONSTRUCTION DATA
InlIne PorTeD CenTer PorTeD
1.38 35
9.79 249
10.62 270
11.76 299
5.45 138
3.04 77
A
2X 1.75 44
.38 10
4.88 124
6.16 157
4X .31 8
6.56 167
3.63 92
4X .38 10
1.
2.
.125 [3mm]
B.1 REMOVED ALL TABULATED DIMENSIONS EXCEPT "A" MF 4/23/2010
A.1 RELEASED FOR GENERAL USE MF 2/4/2010
REV REVISION CHG DATE APP DATE ECN
Standard Integral
Muffler Option
Mesh & Sound
Dampening Muffler
Option
A 7.13 [181] 8.81 [224]
THIS IS A PROPRIETARY DOCUMENT. DO NOT REPRODUCE OR DISCLOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF IDEX AODD
MADE FROM
ASS'Y REFERENCE PUMP REFERENCE
MATERIAL
PART NUMBER
DESCRIPTION
DRAWING NUMBER
IDEX AODD
REV B.1
UNLESS OTHERWISE SPECIFIED
TOLERANCES
.XX .XXX .010 .005
ANGULAR 1/2
SURFACE FINSH 63
DO NOT SCALE DRAWING DIMENSIONS ARE INCHES
SHEET
C
6 7 8
A
8 7 6 5 4 3 2 1
D
B
D
C
B
A
450.467.000
OUTLINE, PUMP, S05, ONE PIECE MANIFOLD
1 2 of
S05 NON-METALLIC
SUCTION PORT
1/2" FNPT
SUCTION PORT (OPTIONAL)
1/2" FNPT
DISCHARGE PORT (OPTIONAL)
1/2" FNPT
AIR INLET
1/4 FNPT
DISCHARGE PORT
1/2" FNPT
MTG. SLOT
MTG. HOLE
STANDARD INTEGRAL MUFFLER
GENERAL NOTES
OPTIONAL SUCTION & DISCHARGE SIDE PORTS WILL BE PLUGGED AT
FACTORY, NOT SHOWN
STANDARD INTEGRAL MUFFLER (SHOWN) COVERS 3/8" FNPT EXHAUST
PORT FOR OPTIONAL MUFFLER STYLES OR PIPING EXHAUST AIR IN
SUBMERGED APPLICATIONS
S05 NON-METALLIC
IN-LINE PORTED OPTION
DIMENSIONAL TOLERANCE =
11.54 293
10.11 257
SUCTION PORT
1/2" FNPT (INTERNAL)
1" MNPT (EXTERNAL)
DISCHARGE PORT
1/2" FNPT (INTERNAL)
1" MNPT (EXTERNAL)
A
.07 2
5.45 138
9.79 249
1.38 35
3.07 78
1.75 44
1.48
1.75 44
AIR INLET
1/4 FNPT
MANIFOLD CAN ROTATE 90
FROM VERTICAL CENTERLINE
3.63 92
6.56 167
4X .36 9
MTG. SLOT
STANDARD INTEGRAL MUFFLER
GENERAL NOTES
OPTIONAL SUCTION & DISCHARGE PORTS AVAILALBE IN 1" BSP 1.
(INTERNAL) AND 1" BSP (EXTERNAL)
STANDARD INTEGRAL MUFFLER (SHOWN) COVERS 3/8" FNPT EXHAUST 2.
PORT FOR OPTIONAL MUFFLER STYLES OR PIPING EXHAUST AIR IN
SUBMERGED APPLICATIONS
S05 NON-METALLIC
CENTER PORTED OPTION
DIMENSIONAL TOLERANCE = .125 [3mm]
D.1 REVISED DRAWING MF 4/23/2010
REV REVISION CHG DATE APP DATE ECN
Standard Integral
Muffler Option
Mesh & Sound
Dampening Muffler
Option
A 7.13 [181] 8.81 [224]
THIS IS A PROPRIETARY DOCUMENT. DO NOT REPRODUCE OR DISCLOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF IDEX AODD
MADE FROM
ASS'Y REFERENCE PUMP REFERENCE
MATERIAL
PART NUMBER
DESCRIPTION
DRAWING NUMBER
IDEX AODD
REV D.1
UNLESS OTHERWISE SPECIFIED
TOLERANCES
.XX .XXX .010 .005
ANGULAR 1/2
SURFACE FINSH 63
DO NOT SCALE DRAWING DIMENSIONS ARE INCHES
SHEET
C
6 7 8
A
8 7 6 5 4 3 2 1
D
B
D
C
B
A
450.319.001
OUTLINE, PUMP, S05, CENTER PORTED
1 2 of
S05 NON-METALLIC
CaUTIon: Nonmetallic pumps and plastic components are not UV stabilized. Ultraviolet radiation can damage these parts and negatively affect material
properties. Do not expose to UV light for extended periods of time.
nitrile General purpose, oil-resistant. Shows good solvent, oil, water and hydraulic fluid resistance. Should not be used with highly polar
solvents like acetone and MEK, ozone, chlorinated hydrocarbons and nitro hydrocarbons.
PVDF A durable fluoroplastic with excellent chemical resistance. Excellent for UV applications. High tensile strength and impact resistance.
nylon 6/6 High strength and toughness over a wide temperature range. Moderate to good resistance to fuels, oils and chemicals.
PTFe Chemically inert, virtually impervious. Very few chemicals are known to react chemically with PTFE: molten alkali metals, turbulent
liquid or gaseous fluorine and a few fluoro-chemicals such as chlorine trifluoride or oxygen difluoride which readily liberate free fluorine at
elevated temperatures.
santoprene ® Injection molded thermoplastic elastomer with no fabric layer. Long mechanical flex life. Excellent abrasion resistance.
Polypropylene A thermoplastic polymer. Moderate tensile and flex strenght. Resists strong acids and alkalie. Attacked by chlorine, fuming
nitric acid and other strong oxidizing agents.
CaUTIon! Operating temperature limitations are as follows:
materials
maximum* minimum*
operating Temperatures
For specific applications, always consult the Warren Rupp “Chemical Resistance Chart”
190°F -10°F
88°C -23°C
250°F 0°F
121°C -18°C
180°F 32°F
82°C 0°C
220°F -35°F
104°C -37°C
275°F -40°F
135°C -40°C
180°F 32°F
82°C 0°C
Maximum and Minimum Temperatures are the limits for which these
materials can be operated. Temperatures coupled with pressure affect the
longevity of diaphragm pump components. Maximum life should not be
expected at the extreme limits of the temperature ranges.