Lincoln Electric IM994 RED-D-ARC LN-25 PRO EXTREME (CE) - Manual (Page 22)

B-5 OPERATION B-5
POWER-UP SEQUENCE
All of the LEDʼs will briefly illuminate during power-up.
If the gun trigger is activated during power up, the
feeder will not operate until the gun trigger is released.
1. WIRE FEED SPEED/AMPERAGE
DISPLAY
Idle
The left display shows the wire feed speed. The right
display is blank. The wire feed speed LED is lit.
Welding
The left display shows the amperage and the right dis-
play shows the arc voltage. If the wire feeder is con-
nected for electrode negative welding, then the volt-
age display shows a minus sign. The amperage and
voltage LEDs are lit.
After Welding
The display continues to hold the value of the amper-
age and arc voltage for five seconds after welding
stops. The amperage and voltage displays flash.
Set-Up Menu
To enter the set-up menu, use paper clip to press the
small button located on the case front.
RED-D-ARC LN-25™ PRO DUAL POWER (CE)
A V ER TISSEM EN T AV WFS
A V E R T I S S E M E N T
A V
WFS
AV E R T IS S E M E NT AV AMPS VOLTAGE
A V E R T I S S E M E N T
A V
AMPS VOLTAGE
6 AV ERTI SSE M E NT ARNI N RE A I N A V 0 OFF 1 V-3 50, V-4 50 2 C V- 305 3 C V- 400 , D C -4 00 5 C V- 655 , D C -6 55 6 1 - 1 0 AV ERTISS EM EN T ARNIN RE A I N V AV ERTI SSEM ENT ARNI N RE A I N V A BUTTON
6
A V E R TI S S E M E N T
A R N I N
R E A I N
A V
0 O FF
1 V- 3 5 0 , V- 4 5 0
2 C V- 3 0 5
3 C V- 4 0 0 , D C - 4 0 0
5 C V- 6 5 5 , D C - 6 5 5
6 1 - 1 0
A V E R T I S S E M E N T
A R N I N R E A I N
V
A V E R TI S S E M E N T
A R N I N R E A I N
V A
BUTTON
Wire Feed Speed Units
Rotate the WFS knob to
the left to use
“inches/minute” for the
wire feed speed units.
Rotate the WFS knob to
the right to use
“meters/minute” for the
wire feed speed units.
Press the set-up button again.
RUN-IN (K2614-1,-2 DUAL POWER FEEDERS
ONLY)
“Run-in” refers to the wire feed speed during the time
from when the trigger is pulled to when an arc is
struck.
When Run-in is “ON”, the wire feed speed is reduced
until an arc is struck. Factory setting is Run-In “OFF”.
Model Run-in Wire Feed Speed
Extra Torque Models 25 in/min
Standard Speed Models 50 in/min
When Run-in is “OFF”, the wire feed speed is the
same as the welding wire feed speed. Turn Run-In
“OFF” for fast, crisp starts, especially when running
with .035 or .045 (0.9 or 1.2mm) solid steel wires at
high wire feed speeds.
Rotate the WFS knob to
the left to turn Run-In
OFF.
Rotate the WFS knob to
the right to turn Run-In
ON.
US
A A O O
O O WFS V
LN-25 PRO
U o r E
A A O O
O O WFS V
LN-25 PRO
r OF F u n
A A O O
O O WFS V
LN-25 PRO
r O
A A O O
O O WFS V
LN-25 PRO
u n n