Vestil AHA-KIT Come-Along kit - Manual (Page 2)

rev. 1/10/2013 Come-along, manual
Hazard Identification--Explanation of SIGNAL WORDS
This manual uses SIGNAL WORDS to indicate the likelihood of personal injuries, as well as the probable
seriousness of those injuries, if the product is misused in the ways described. Other signal words call attention to
uses of the product likely cause property damage.
The signal words used appear below along with the meaning of each word:
Identifies a hazardous situation which, if not avoided, WILL result in DEATH or
SERIOUS INJURY. Use of this signal word is limited to the most extreme
situations.
Identifies a hazardous situation which, if not avoided, COULD result in DEATH or
SERIOUS INJURY.
Indicates a hazardous situation which, if not avoided, COULD result in MINOR or
MODERATE injury.
Identifies practices likely to result in product/property damage, such as operation that
might damage the product.
Each person who assembles, installs, uses, or maintains this product should read the entire manual in advance
and fully understand the directions. If after reading the manual you do not understand an instruction, ask
your supervisor or employer for clarification, because failure to adhere to the directions in this manual
might result in serious personal injury.
SAFETY GUIDELINES
Vestil diligently strives to identify foreseeable hazards associated with the use of its products. However, material
handling is inherently dangerous and no manual can address every conceivable risk. The end-user ultimately is
responsible for exercising sound judgment at all times.
Electrocution might result if any part of the crane, come-along kit, hoist or load contacts electrified wires.
Reduce the likelihood of electrocution by applying common sense:

DO NOT contact electrified wires with any part of the crane, come-along, hoist or load;
 DO NOT adjust the height of your crane in a location where contact with electrified wires will or is likely to occur.
If this product is used improperly or carelessly, the operator and/or bystanders might sustain serious
personal injuries. ALWAYS use the product properly:
 Failure to read and understand the entire manual before assembling, installing, using or servicing the
product constitutes misuse. Read the manual to refresh your understanding of proper use and maintenance
procedures as necessary.
 ONLY use the components of the come-along kit to adjust the height of AHA and AHS series gantry cranes. DO NOT
use the kit as a hoist or winch.
 ONLY use this kit to adjust the height of an unloaded crane. Disconnect all loads from the crane/hoist and either
secure in a fixed position or remove the hoist before using the kit to adjust the height of your crane.
 Inspect the come-along and the cable loops before each use. DO NOT use this device if the inspection reveals
structural damage. Examples of structural damage include: 1) fraying, stretching, tearing, etc. of the cable loops; 2)
corrosion, severe wear, or other condition that affects the function or the integrity of the come-along. Immediately tag
out the come-along and replace each part that fails to pass an inspection. DO NOT use the product until it is fully
restored to normal condition. ONLY use manufacturer-approved replacement parts.
 DO NOT use the product if any unusual noise or movement is observed. If a malfunction occurs, remove the unit from
service and notify your supervisor or maintenance personnel about the issue.
 DO NOT use the come-along in place of the height adjustment pins. The come-along is a means ONLY for adjusting
the height of your crane. Complete the height adjustment and reinsert the pins
 DO NOT remove or obscure any label. All product labels must be readable and undamaged.
 DO NOT modify the any part of the come-along in any way UNLESS you first obtain written approval from Vestil.
Unauthorized modifications automatically void the limited warranty (see p. 5) and might make the come-along
unsafe to use.
Proper use, maintenance, and storage are essential for this product to function properly.
o Always use this product in accordance with the instructions in this manual and consistent with any relevant training.
o Store the come-along someplace where it will remain dry.
o Periodically grease pivot points as needed to maintain smooth operation.
Copyright 2013 Vestil Manufacturing Corp. Page 2 of 5