Av/d installation instructions, Installation, Disposal – TREND AV_D User Manual
Page 4: Trend control systems limited, Trend control systems usa, Replace sensor cover, Switch on supply to controller, Configure iq (not iql17/vav), Set up sensor scaling, Test system
4
AV/D Duct Air Velocity Sensor Installation Instructions TG200504 Issue 2 11/07/08
AV/D
Installation Instructions
Trend Control Systems Limited
P.O. Box 34, Horsham, West Sussex, RH12 2YF, UK. Tel:+44 (0)1403 211888 Fax:+44 (0)1403 241608 www.trend-controls.com
Trend Control Systems USA
6670 185th Avenue NE, Redmond, Washington 98052, USA. Tel: (425)897-3900, Fax: (425)869-8445 www.trend-controls.com
Please send any comments about this or any other Trend technical publication to [email protected]
© 2008 Honeywell Technologies Sàrl, ECC Division. All rights reserved. Manufactured for and on behalf of the Environmental and Combustion Controls
Division of Honeywell Technologies Sàrl, Ecublens, Route du Bois 3, Switzerland by its Authorized Representative, Trend Control Systems Limited.
Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without
obligation to notify any person of such revisions or changes.
Installation
(continued)
Replace sensor cover
12
Switch on supply to controller
13
O
I
Configure IQ (not IQL17/VAV)
14
I Q
I Q
or
IQ Configuration Manual 90-1533
Set up sensor scaling
15
Test system
16
It is recommended to use SET (Software Tool) for the setting of the sensor type module. For all IQ2 series controllers with
firmware version 2.1 or greater, or IQ3 series controllers use the appropriate SET Unique Sensor References from the
following:
Δ
V
controller
tighten 4 screws
Note that if AV/D is left at default link settings, IQL17/VAV
requires no sensor scaling configuration.
If IQ
WEEE Directive :
At the end of their useful life the packaging
and product should be disposed of by a
suitable recycling centre.
Do not dispose of with normal household waste.
Do not burn.
Disposal
Alternatively enter scaling manually as
defined in the adjacent table with sensor
type scaling mode set to 5 (characterise).
Note that for IQ3, scaling mode and
exponent do not need to be set up.
For all other controllers see Sensor Scaling
Reference Card TB100521A.
e
g
n
a
R
k
n
i
L
Y
E
U
L
P
I1
I2
O1 O2
tl
u
a
f
e
d
)
s
/
m
0
1
(
tl
o
V
,
V
)
s
tl
o
v
(
0
2
1
.
0
1
0
2
0
0
1
0
0
1
t
n
e
r
r
u
C
,I
)t
n
e
r
r
u
c
(
2
2
1
.
0
1
0
2
4
0
2
0
0
1
s
/
m
5
1
s
tl
o
V
,
V
)
s
tl
o
v
(
0
2
1
.
5
1
0
2
0
0
1
0
5
1
t
n
e
r
r
u
C
,I
)t
n
e
r
r
u
c
(
2
2
1
.
5
1
0
2
4
0
2
0
5
1
s
/
m
0
2
s
tl
o
V
,
V
)
s
tl
o
v
(
0
2
1
.
0
2
0
2
0
0
1
0
0
2
t
n
e
r
r
u
C
,I
)t
n
e
r
r
u
c
(
2
2
1
.
0
2
0
2
4
0
2
0
0
2
d
e
k
n
i
L
V
0
1
o
t
0
7
p
e
t
S
s
m
0
1
V
y
ti
c
o
l
e
V
)
T
L
U
A
F
E
D
(
d
e
k
n
i
L
A
m
0
2
o
t
4
7
p
e
t
S
s
m
0
1
I
y
ti
c
o
l
e
V
s
m
5
1
V
y
ti
c
o
l
e
V
s
m
5
1
I
y
ti
c
o
l
e
V
s
m
0
2
V
y
ti
c
o
l
e
V
s
m
0
2
I
y
ti
c
o
l
e
V