Server SE-xxx EXPRESS - Manual (Page 4)

PUMP DISASSEMBLY
1 REMOVE CONNECTOR FROM FLEXIBLE PLASTIC
TUBE.
2 ROTATE AND PULL CONNECTOR AWAY FROM
FLEXIBLE PLASTIC TUBE.
3 REMOVE FLEXIBLE PLASTIC TUBE FROM BOTTOM
OF PUMP HOUSING.
4 ROTATE AND PULL FLEXIBLE PLASTIC TUBE AWAY
FROM PUMP HOUSING.
5 REMOVE PUMP DOME FROM PUMP HOUSING.
6 UNHOOK LOOP FROM BOTTOM OF DOME TO
RELEASE DOME FROM PUMP HOUSING.
7 TAKE PINCH VALVE OUT OF PUMP HOUSING.
PUMP ASSEMBLY
ALWAYS CLEAN PUMP THOROUGHLY BEFORE EACH USE.
SEE UNIT TAKE-DOWN, PUMP DISASSEMBLY, PUMP
ASSEMBLY, SAFETY GUIDELINES, AND CLEANING.
1 INSERT PINCH VALVE INTO PUMP HOUSING.
2 INSTALL DOME ONTO PUMP BODY.
•
Align valve flap inside dome to be on top of
opening between pump body and pump body
discharge tube.
•
Place loop onto pump housing tube to secure
dome.
3 INSTALL FLEXIBLE TUBE ONTO PUMP BODY
SHORT EXTENSION TUBE.
•
Use small amount of water as lubricant when
installing flexible tube.
•
Rotate flexible tube onto pump body short
extension tube until projections on pump body
short extension tube align with holes in flexible
tube.
•
Rotate and position flexible tube with connector
on opposite end to be pointing away from
pump body discharge tube.
4 INSTALL CONNECTOR ONTO FLEXIBLE TUBE.
•
Use small amount of water as lubricant when
installing connector.
•
Rotate connector into flexible tube until
projections on connector align and fall into
holes in flexible tube.
5 INSTALL DISCHARGE FITTING ONTO PUMP
HOUSING DISCHARGE TUBE.
•
Place loop of discharge fitting onto peg on end
of discharge tube to secure discharge fitting.
CLEANING PUMP
BEFORE FIRST USE DISASSEMBLE AND CLEAN UNIT.
STAINLESS STEEL PARTS CAN CORRODE. IT IS
IMPORTANT TO CLEAN, RINSE, SANITIZE, AND DRY
THESE PARTS DAILY AND PROPERLY. FAILURE TO
COMPLY WITH ANY OF THESE INSTRUCTIONS MAY
VOID UNIT WARRANTY:
1 SEE UNIT TAKE DOWN
2 FLUSH AND RINSE PUMP IN A CONTAINER OF
WARM WATER.
•
Be sure to flush and rinse connector and
discharge tube thoroughly.
•
Place lower end of pump into water container
and operate pump until all (if any) remaining
product is expelled and only the warm water
flows from the discharge tube. Then remove
pump from container of water to disassemble.
3 DISASSEMBLE PUMP. SEE PUMP DISASSEMBLY.
4 WASH AND SCRUB ALL PARTS WITH
DISHWASHING DETERGENT AND HOT WATER
DAILY.
• Use supplied brushes to clean all confined areas.
• Do not use abrasive cleansers, scrapers, steel
pads, steel wool, or other cleaning tools that can
scratch surfaces.
• A general purpose, nonabrasive cleaner may be
used on hard to remove food deposits.
• Do not use cleansing agents with high
concentrations of acid, alkaline or chlorine. These
agents can corrode stainless steel.
• Do not use ammonia to clean pump parts.
Ammonia can damage plastic parts.
• A nontoxic glass cleaner may be used for
cleaning any stainless steel parts.
5 FULLY RINSE ALL PARTS THOROUGHLY WITH
CLEAR WATER.
• Fully rinsing all parts can help prevent corrosion.
6 DRY ALL STAINLESS STEEL PARTS WITH A CLEAN
SOFT CLOTH.
• Various elements and minerals, such as chlorides
in tap water, can accumulate on stainless steel
parts and create corrosion.
• To prevent corrosion on any stainless steel parts,
it is important to fully dry with a clean soft cloth
regularly.
7 SANITIZE PARTS FOLLOWING LOCAL
SANITIZATION REQUIREMENTS. ALL PARTS IN
CONTACT WITH FOOD MUST BE SANITIZED.
• Allow parts to fully air dry after sanitization.