MaxPower Corp UniStar P Tower - Manual (Page 5)

Tower Models SC60021T SC60022T SC80021T SC80022T SC11021T SC11022T
INPUT
Connection
Hardwire / Optional 6ft. Line
Cord with L6-30P Plug
Hardwire
Voltage Range 160 -280Vac
Frequency 45 ~ 65 Hz
Phase/Wire Single, Line + Common + Ground
Power Factor Up to 0.99 at 100% Linear Load
Current THD <5% at 100% Linear Load
OUTPUT
Connection Hardwire
Voltage
208/120 or
240/120Vac
208/220/230/
240Vac
208/120Vac or
240/120Vac
208/220/230/
240Vac
208/120 or
240/120Vac
208/220/230/
240Vac
Voltage Adjustment +/- 0%; +/- 1%; +/- 2%; +/- 3% For All Voltages
Voltage Regulation +/- 2%
Capacity 6000VA/4200W 8000VA/5600W 10000VA/7000W
Parallel Capability Redundancy or Capacity – 4 Units
Rated Power Factor 0.7 Lagging
Wave Form Sine Wave, THD < 3% (no load to full load)
Frequency Stability +/- 0.2% (Free Running)
Frequency Regulation +/- 1 Hz
Transfer Time 0ms/instantaneous
Crest Factor 3:1
Effi ciency
(AC to AC Nominal)
91%
Effi ciency
(AC to AC ECO Mode)
Up to 97% Up to 93%
Leakage Current < 3mA @ Full Load
Manual Bypass Switch Make – Before - Break
DC Start Yes
Cooling Load Dependant Variable Speed Fans
DISPLAY, ALARMS, DIAGNOSTICS, COMMUNICATIONS & EMERGENCY FUNCTION
Status On LED + LCD
Line Mode, Backup Mode, ECO Mode, Bypass Supply, Battery Low, Battery Bad/Disconnected,
Overload, Transferring with interruption & UPS Fault
Readings On LED + LCD
Input Voltage, Input Frequency, Output Voltage, Output Frequency, Load Percentage,
Battery Voltage & Unit’s Inner Temperature
Self-Diagnostics Upon Power-on, Front Panel Setting & Software Control, 24 Hour self check
Audible Alarms and Visual Line Failure, Battery Low, Transfer to Bypass, System Fault Conditions
Communications RS232 Serial Port ( 2 slots available for optional SNMP/WEB, USB or Dry Contact Card)
Emergency Power Off
(EPO) Connection
Emergency Power Off shuts down UPS when activated by customer supplied EPO Circuit
PHYSICAL
Dimensions (H x W x D) 29.5" x 11.4" x 25.4" 34.7" (21 T ) , 29.5" (22 T ) x 11.4" x 25.4" 34.7" (21 T ) , 29.5" (22 T ) x 11.4" x 25.4"
Weight (lbs.) 265 (21T), 190 (22T) 320 (21T), 203 (22T) 340 (21T), 223 (22T)
Safety and Performance
UL1778, c-UL; CE – FCC Class A, N 50091-2, EN 61000 (various),
IEC 61000 (various), IEC 62040-2, CISPR 22
INTERNAL BATTERY
Battery Run Time@Full
Load
8 7 5
Type
Sealed Lead Acid Maintenance
Free, 20 each 12V/7AH, 240Vdc
Sealed Lead Acid Maintenance
Free, 20 each 12V/9AH, 240Vdc
Sealed Lead Acid Maintenance
Free, 20 each 12V/9AH, 240Vdc
Hot – Swap Batteries Yes
Recharge Time 4 hours to 90% 5 hours to 80%
*Extended Run Time
Battery Cabinets SC-BP6000T-2, SC-BP6000T-3, SC-BP1100T-2, SC-BP1100T-3
(Refer To Run Time Chart)
OPTIONAL COMMUNICATION Cards and Shutdown Software
SC-SNMP1 SNMP/WEB Network Card & Shutdown Software
SC-Contact/EPO Dry Contact & EPO Card
SC-PK Parallel Cable kit contains two RJ45 cables and miscellaneous hardware for paralleling
Note: (2) slots available; both cards can be used simultaneously; RS232 Port is disabled when communication cards are installed.
OPTIONAL EXTERNAL EXTENDED BATTERY CABINETS
Model SC-BP6000T-2 & -3 SC-BP1100T-2 & -3
Type
Sealed Lead Acid Maintenance Free,
-2: 40 each & -3: 60 each 12V/9AH, 240Vdc
Sealed Lead Acid Maintenance Free,
-2: 40 each & -3: 60 each 12V/9AH, 240Vdc
Hot – Swap Cabinets Yes
Battery Connection Connector
Dimensions (H x W x D) 29.5" x 11.4" x 25.4"
Weight (lbs.) 326
OPTIONAL EXTENDED BATTERY PACK CHARGER
SC-CHG-1000
1000W External Mount Battery Charger (1) charger per
every (2) External Battery Packs Required
3.4"H x 6.6"W x 11.1"D 7 lbs.
OPTIONAL PARALLEL DISTRIBUTION / BYPASS MODULE (Note 1)
SC-PKIT-2 Parallel Distribution Bypass 60Amp for (2) UPS Modules 3.7"H x 10.5"W x 9.5"D 11 lbs.
SC-PKIT-4 Parallel Distribution Bypass 120Amp for (4) UPS Modules 3.7"H x 10.5"W x 16.4"D 20 lbs.
Notes:
Parallel for capacity confi gurations can use (1) battery system sized for the ultimate capacity.
Parallel for redundancy confi gurations require (1) battery system for each UPS.
Tower Models