Mallory Ignition ACCEL DIGITAL NITROUS PROCESSOR 74186 - Manual (Page 5)

5 ACCEL/DFI TECHNICAL SUPPORT 248.380.2780 www.accel-dfi.com
INSTALLATION
WHAT YOU SHOULD KNOW
Please read these instructions carefully before installing your
Digital Nitrous Processor.
Important Tips
• Do not use solid core spark plug wires with this unit. It contains
digital electronics and will NOT function correctly with solid
core wires.
• Do not install harness or run Points Input / Output wires near
spark plug wire or ignition coil. Mount the Processor as far
away from secondary ignition components (coil, ignition wires,
etc.) as physically possible.
• This unit is not water resistant or water proof, we suggest that
it is mounted in the passenger compartment so as not to get
wet from rain, car washing or a liquid of any type!
• The Handheld programmer buttons are very delicate and can
be damaged by misuse and/or carelessness. Programmers that
have been determined to be damaged due to neglect will NOT
be covered under warranty.
Safety Tips, Please Read
• It is the responsibility of the purchaser to follow all guidelines
and safety procedures supplied with this product and any other
manufacturer’s product used with this product.
• Follow all recommended safety guidelines from this and other
manufacturer’s installation guides.
• It is also the responsibility of the purchaser to determine
compatibility of this device with the vehicle and other components.
• ACCEL DFI Corporation assumes no responsibility for damages
resulting from accident, improper installation, misuse, abuse,
improper operation, lack of reasonable care, or all previously
stated reasons due to incompatibility with other manufacturer’s
products.
• ACCEL DFI Corporation assumes no responsibility or liability
for damages incurred from the use of products manufactured
or sold by Accel DFI Corporation on vehicles used for
competition racing.
• ACCEL DFI Corporation neither recommends nor approves the
use of its products on vehicles which may be driven on public
highways or roads, and assumes no responsibility for damages
incurred from such use.
• It is the purchaser’s responsibility to check the state and local
laws pertaining to the use of Nitrous Oxide for racing applications.
ACCEL DFI Corporation does not recommend nor condone the
use of its products for illegal street racing.
INSTALLATION OF THIS PRODUCT SIGNIFIES THAT YOU HAVE
READ THIS DOCUMENT AND AGREE TO THE TERMS STATED WITHIN.
Due to the technical nature of ACCEL DFI products, we are unable
to answer technical questions via the Internet. If you have any
questions, Please call the ACCEL DFI Technical Support hotline.
Tech Line: 1-248-380-2780 from 8:30 am – 6 pm, Monday-
Friday, Eastern Standard Time.
Please fill out and mail your warranty card.
WARRANTY
FACTORY DIRECT LIMITED WARRANTY. ALL ACCEL/DFI
PRODUCTS* ARE WARRANTED AGAINST DEFECTS IN MATERIALS
OR WORKMANSHIP. ACCEL/DFI LIABILITY UNDER THIS WARRANTY
SHALL BE LIMITED TO THE PROMPT REPAIR CORRECTION OR
REPLACEMENT OF ANY DEFECTIVE PART OF THE PRODUCT
WHICH ACCEL/DFI DETERMINES TO BE NECESSARY. THIS LIMITED
WARRANTY IS TO THE ORIGINAL PURCHASER FOR AS LONG AS
HE OR SHE OWNS THE VEHICLE ON WHICH THE PRODUCT IS
ORIGINALLY INSTALLED, PROVIDING ALL THE INFORMATION
REQUESTED IS FURNISHED. YOU MUST RETAIN A COPY OF YOUR
ORIGINAL SALES INVOICE OR RECEIPT. WITHOUT PROPER
DOCUMENTATION, THIS WARRANTY IS VOID.
RESOLD UNITS ARE NOT COVERED UNDER THIS WARRANTY.
CAUTIONS AND WARNINGS
1. Always follow safety & installation guidelines and precautions
when installing this and any other related component.
2. Always remove both battery cables when installing new
electrical components and/or wiring.
3. Always use Circuit protection (Fuses) where required.
4. Wire in all your connections with the Processor disconnected.
5. Connect ground wires directly to battery negative terminal or
at battery negative cable end.
6. Test system for proper operation after completing installation.
PARTS INCLUDED
1 ACCEL/DFI Digital Nitrous Processor
1 Handheld Programmer
1 Handheld Programmer Cable
1 8-way Processor Control Harness
1 4-way Processor Power Harness
1 Magnetic Pickup Harness
1 NO2 Solenoid Harness
RECOMMENDED PARTS NOT SUPPLIED
Parts Part #
1 NO2 Single Stage System
1 Accel/DFI 6A or DFI 6A 75606 - DFI Pro 7 75609
PRO 7 CD Ignition Box
1 Accel DFI “E” Core DFI “E” Core 75607 - DFI Pro 7 75608
or Pro 7 Coil
1 Micro Switch
1 Lighted Toggle Switch
1 Firewall Rubber Grommet
(To keep wires from chafing
on metal edge)