Mallory Ignition Mr_Gasket clutch cover 5325 - Manual

GENERAL INFORMATION
The Mr. Gasket Aluminum Cover for Air Conditioner Clutch fits
1978-93 GM cars and trucks with a radial A/C compressor.
INSTALLATION PROCEDURE
Step 1
Clean threads on inside of the clutch using solvent and a small
wire brush.
Step 2
Turn the ignition key forward WITHOUT STARTING ENGINE
to accessory 12V power and slide the A/C - Heater lever to
defrost. This will lock the compressor clutch. NOTE: Before
completing this step, unplug distributor to prevent module
from burning up.
Step 3
Apply thread locker onto end of threaded adapter that is
counter-bored (right hand thread) and install into clutch. Use
adjustable pliers to tighten the adapter securely.
Step 4
Install ¼”-28 set screw into threaded adapter using a 1/8” hex
key wrench and securely tighten.
Step 5
Apply thread locker onto the end of threaded adapter and in-
stall clutch cover (left hand thread) onto adapter securely. Turn
ignition key to OFF position.
Step 6
Allow thread locker 90 minutes to dry. Make sure to plug back
in distributor.
QUESTIONS
Please call our Tech Support line at 1-216-688-8300, M – F, 9 –
5 EST. Please have the part number on hand when you call.
INSTALLATION INSTRUCTIONS
ALUMINUM COVER FOR AIR CONDITIONER CLUTCH – Mr. Gasket Part No. 5325
FORM 53252012
Read all instructions carefully before beginning installation. Installation on vehicles equipped with a mechanical cooling fan
requires checking the distance between fan blades and compressor for adequate clearance for clutch cover.
MR. GASKET IS A TRADEMARK OF PRESTOLITE PERFORMANCE
10601 Memphis Ave. #12, Cleveland, OH 44144
216.688.8300 FAX 216.688.8306
www.mr-gasket.com
FORM 53252012
06/12
Printed in U.S.A.
GENERAL INFORMATION
The Mr. Gasket Aluminum Cover for Air Conditioner Clutch fits
1978-93 GM cars and trucks with a radial A/C compressor.
INSTALLATION PROCEDURE
Step 1
Clean threads on inside of the clutch using solvent and a small
wire brush.
Step 2
Turn the ignition key forward WITHOUT STARTING ENGINE
to accessory 12V power and slide the A/C - Heater lever to
defrost. This will lock the compressor clutch. NOTE: Before
completing this step, unplug distributor to prevent module
from burning up.
Step 3
Apply thread locker onto end of threaded adapter that is
counter-bored (right hand thread) and install into clutch. Use
adjustable pliers to tighten the adapter securely.
Step 4
Install ¼”-28 set screw into threaded adapter using a 1/8” hex
key wrench and securely tighten.
Step 5
Apply thread locker onto the end of threaded adapter and in-
stall clutch cover (left hand thread) onto adapter securely. Turn
ignition key to OFF position.
Step 6
Allow thread locker 90 minutes to dry. Make sure to plug back
in distributor.
QUESTIONS
Please call our Tech Support line at 1-216-688-8300, M – F, 9 –
5 EST. Please have the part number on hand when you call.
INSTALLATION INSTRUCTIONS
ALUMINUM COVER FOR AIR CONDITIONER CLUTCH – Mr. Gasket Part No. 5325
FORM 53252012
Read all instructions carefully before beginning installation. Installation on vehicles equipped with a mechanical cooling fan
requires checking the distance between fan blades and compressor for adequate clearance for clutch cover.
MR. GASKET IS A TRADEMARK OF PRESTOLITE PERFORMANCE
10601 Memphis Ave. #12, Cleveland, OH 44144
216.688.8300 FAX 216.688.8306
www.mr-gasket.com
FORM 53252012
06/12
Printed in U.S.A.