Liquid Controls IT300N - Manual (Page 11)

9
PROGRAMMING FLOWCHART
(continued)
Press the key to step the totalizer decimal to the desired location.
Press the E key to enter the displayed decimal location.
Press the M key to skip and keep the existing location
Press the key to step to the desired totalizer descriptor.
Press the E key to enter the displayed descriptor.
Press the M key to skip and keep the existing descriptor.
NOTE: When option "D" (rate per day) is ordered; selections are:
GAL, BBL, MCF, M3, "blank"
Press the key to step to the desired scale setting.
Press the E key to enter the displayed scale setting.
Press the M key to skip and keep the existing setting.
NOTE: When option "D" (rate per day) is ordered; selections are:
min, sec, days
Press the key to step the ratemeter decimal to the desired location.
Press the E key to enter the displayed decimal location.
Press the M key to skip and keep the existing location
Press the key to increment each individual digit of the delay.
Press the
key to advance to the next digit.
Press the E key to enter the displayed value.
Press the M key to skip and keep the existing value.
Press the key to increment each individual digit of the out low setting (4mA
value). This will only display on units with Analog Output.
Press the key to advance to the next digit.
Press the E key to enter the displayed value.
Press the M key to skip and keep the existing value.
Press the key to increment each individual digit of the out high setting
(20mA value). This will only display on units with Analog Out-
put.
Press the key to advance to the next digit.
Press the E key to enter the displayed value.
Press the M key to skip and keep the existing value.
Press the key to step to the desired pulse scale divider for the pulse
output.
Press the E key to enter the displayed pulse scale divider.
Press the M key to skip and keep the existing pulse scale value.
Press the key to step to the desired pulse width for the pulse output.
Press the E key to enter the displayed pulse width.
Press the M key to skip and keep the existing pulse width.
This will not display if Pulse Out is turned OFF.
Press the key to increment each individual digit of the "nor" factor.
Press the E key to enter the displayed value.
Press the M key to skip and keep the existing value.
Press the key to step to the desired lock setting.
Press the E key to enter the displayed lock setting.
Press the M key to skip and keep the existing setting.
Press the key to increment each individual digit of the lock code.
Press the
key to advance to the next digit.
Press the E key to enter the displayed value.
Press the M key to skip and keep the existing value.
TDEC
12345678
ToT DESC
SEC
r SCALE
TOTAL DECIMAL
SCALE
(ratemeter)
SEC
NNIN
HRS
( Days)
GAL
LIT
FT3
M3
"blank"
(BBL, MCF)
1234
R DECLoC
E
M
E
M
E
M
E
M
0.1
delay
0000
oUT Lo
99999
oUT HI
D 1
Pul scale
OUT LOW
(4mA)
OUT HIGH
(20mA)
PULSE
SCALER
(divider)
D 1 D 1
D 10 D 10
D100 D100
oFF oFF
0.1 to 99.9
E
M
E
M
E
M
E
M
.5 .5
p uuidth
E
M
.5
.25
.125
.0625
PULSE
WIDTH
(seconds)
1
nor
NORMALIZATION NORMALIZA NORMALIZA
E
M
Continued From Previous Page
RUN MODE
0000
loc code
LOCK
CODE
E
M
yes
loC UnIt
TURN LOCK
ON or OFF
yes
no
E
M
TOTAL
DESCRIPTOR
RATE RA RA
DECIMAL
LOCATION LOCA LOCA
DELAY DELA DELA
(Dampening)