LEADER LV7800 - Manual (Page 7)

31
Measured Signal
Supported Standards
Input
Composite Video
Input Connector
Maximum Input Voltage
Output
Composite Video
Output Signal
Output Connector
Output Amplitude
Display
WAVE Display
VECTOR Display
PICTURE Display
Waveform Display Section
Vertical Axis
Sensitivity
Gain
Variable Gain
Amplitude Accuracy
Filter
DC Restorer
Horizontal Axis
Operation Mode
Display Format
Line Display
Line Magnification
Field Display
Field Magnification
Time Base Accuracy
LV 58SER03 COMPOSITE VIDEO INPUT UNIT SPECIFICATIONS
Composite video signal (NTSC/PAL)
SMPTE 170M and ITU-R BT.470
Select A or B
BNC connector
±5 V (DC + Peak AC)
Active
BNC connector 1 system 1 connector
1 Vp-p ± 5 %
Waveform display
Vectorscope display
Picture display
V Scale (PAL) -0.3 V to 0.7 V
IRE Scale (NTSC) -40 IRE to 100 IRE
Select x1 or x5
≤ 0.2 to ≥ 2
±1 %
Luminance filter
Clamp to the back porch (fixed)
Overlay Displays only a single waveform
1H or 2H
Select
x1, x10 or x20
1V or 2V
Select
x1, x20 or x40
±1 %
Vectorscope Display Section
Sensitivity
Gain
Variable Gain
Phase Accuracy
Amplitude Accuracy
Phase Adjustment Range
Setup (NTSC)
NTSC Display (PAL)
IQ Axis
SCH
Picture Display
Marker Display
Display Size
Line Select
Image Quality Adjustment
Status Display Section
Display
Display Range
V direction
H direction
Synchronization Signal
Power Consumption
Weight
Accessory
Select 75 % or 100 % Using a color bar
Select x1, x5, or IQ-MAG
0.2 to 2
±2 ˚
±3 %
360˚
Select 0 % or 7.5 %
Select NTSC or PAL display
Select show or hide
Displays the SCH value numerically
16:9 marker display
Safe action marker display
Safe title marker display
Center marker display
Reduced display, full frame display, and actual size
display
Displays a marker for the selected line.
Brightness adjustment, contrast adjustment, RGB
level adjustment, and RGB bias adjustment
Displays the phase difference between the com-
posite signal and external sync signal numerically
and graphically.
Holds and displays eight phase difference values
being measured.
±1/2 frame
±1/2 Line
NTSC/PAL black burst signals
Supplied from the instrument; 9 Wmax.
0.25 kg, 0.5 lbs.
Instruction manual ..............................................1
LV 58SER04 MPEG DECODER Plug-In Unit
The LV 58SER04 is an input unit that
receives MPEG-2 TS (DVB-ASI) audio and
video signals, decodes them, and transfers
them to the LV 5800 (MULTI MONITOR) or
the LV 7800 (MULTI RASTERIZER) to be
displayed. After a signal is decoded, its
video signal waveforms, vectors, pictures,
and audio signals can be displayed. The
LV 58SER04A can also be used to moni-
tor errors defined by ETSI ETR-290, to dis-
play PAT and PMT data, and to display TS
bit rates and the bit rates for each PID.
These features are ideal for continuous
monitoring of MPEG-2 TS signals in
broadcasting stations and similar facilities.
When combined with other units, the LV
58SER04 can also:
• Display eye patterns for DVB-ASI signals
(when combined with the LV 58SER02)
• Display levels and Lissajous curves for
audio signals (when combined with the
LV 58SER40A)
PID TMCC
SFN DVB-ASI STATUS
BIT RATE
Waveform Vector
Leader Instruments Corporation web : http://www.LeaderUSA.com Tel. : 1 (714) 527‐9300
6484 Commerce Drive, Cypress, CA 90630 e‐mail : [email protected] Fax : 1 (714) 527‐7490