Controlled Products Systems Group LA400 User Manual
Page 2
2
OPERATOR SPECIFICATIONS
Tools Needed for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Carton Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Additional Items Needed for Installation . . . . . . . . . . . . . . . . . . . . . . . .3
Operator Dimensions and Specifications . . . . . . . . . . . . . . . . . . . . . . . .3
Model Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
OPERATOR WARNINGS
Safety Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Suggested Entrapment Protection Device Locations . . . . . . . . . . . . . .6
Warnings and Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Warning Sign Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
INSTALLATION
Gate Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Pull-to-Open Mounting Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Push-to-Open Instructions for use with
Optional Accessory Kit 50-19503 . . . . . . . . . . . . . . . . . . . . . . . . . .10-11
Control Box Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
WIRING
Connect Arm to Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Earth Ground Rod Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
BASIC CONTROL BOARD SETUP
Set Dip Switch for Gate Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Programming Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Wire Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Optional Control Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-20
Force and Timer to Close . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Program Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
OPERATION AND MAINTENANCE
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Manual Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
ACCESSORIES
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
WIRING DIAGRAM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
TROUBLESHOOTING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27-28
REPAIR PARTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29-30
When you see these Safety Symbols and Signal Words on the following
pages, they will alert you to the possibility of serious injury or death if
you do not comply with the warnings that accompany them. The hazard
may come from something mechanical or from electric shock. Read the
warnings carefully.
When you see this Signal Word on the following pages, it will alert you
to the possibility of damage to your gate and/or the gate operator if you
do not comply with the cautionary statements that accompany it. Read
them carefully.
Mechanical
Electrical
T A B L E O F C O N T E N T S
T A B L E O F C O N T E N T S
WARNING
CAUTION
WARNING
WARNING
WARNING
CAUTION
WARNING
WARNING
IMPORTANT NOTE
• BEFORE attempting to install, operate or maintain the operator, you
must read and fully understand this manual and follow all safety
instructions.
• DO NOT attempt repair or service of your commercial door and gate
operator unless you are an Authorized Service Technician.
WARNING
CAUTION
WARNING
WARNING
TOOLS NEEDED FOR INSTALLATION
During assembly, installation and adjustment of the operator the tools
listed below will be needed.
• Wrench or Socket Set
• Phillips Head Screwdriver
• C Clamps
• Level
• Small Screwdriver
• T25 Torx Head Screwdriver