Chapin 1999 User Manual

Warning, Pressurizing and spraying, Pressurizing and spraying, continued

Lock

Position

Hazard: Improper use or failure to follow instructions can result in explosive failure causing

serious eye or other injury.

For safe use of this product you must read and follow all instructions.

Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up. Do not store

or le

ave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full

foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.

Never stand with face or body over

top of tank when pumping or loosening pump to prevent eject-

ing pump assembly and/or solution from striking and injuring you. Never pressurize sprayer by any

means other than the original pump. Do not attempt to modify or repair this product except with

original manufacturer’s parts. Never spray flammable materials or heat, pressure, or gas produc-

ing chemicals. Always read and follow manufacturer’s instructions before use with this sprayer

as some chemicals may be hazardous when used with this sprayer.

WARNING!

Sk-1113-1

Repair Parts Kit Gaskets and Seals (not included),

Juego de piezas de reparación, empaquetaduras y juntas (no incluido)

Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus)

6-4629

Printed in U.S.A., Impreso en E.U.A, Imprimé aux U.S.A.

1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.

2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,

replace hose before using. Replace with original manufacturer’s parts only.

3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of

tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank

weakening and could result in explosive bursting under pressure. If any of these signs are found, discard

tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.

4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.

5) Do: Pump plunger 8-10 strokes and inspect for leaks.

6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.

7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and

proceed with Filling, Pressurizing and Spraying Instructions.

3. Pre-Use Check

4. Filling

1) Do: Turn pump handle counterclockwise and remove pump

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.

4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and

tighten securely.

8. To Release Pressure

1 Do: To release pressure in the sprayer just pull the ring on the relief

valve until all pressure is released from the sprayer.

2) Do: Stay away from the sprayer until all air has escaped.

9. Care, Storage and Maintenance

1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing

and Spraying Instructions, except pump unit only 8-10 strokes.

2) Do: Open shut-off and allow water to run through discharge assembly.

3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.

4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.

5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening

in cover.

WARNING:

Handling the brass parts of this product will expose you to lead, a chemical known

to the State of California to cause birth defects and other reproductive harm. Wash hands after

handling.

010325-1 (A) R0209

1. Hose to Tank

2. Nozzle

1-5797

Nozzle .5 GPM

Boquilla

Buse

Parts, Piezas, Pièces

Note:

Your particular sprayer may not include all parts pictured above.

Nota:

Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.

Remarque :

Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.

Attach the hose by screwing the swivel

nut clockwise and tightening to 37 in. lbs.

Refer to Pre-use check before using.

Congratulations!

You have just purchased a quality Chapin product.

Do Not Return To Store.

Call us @ 1-800-950-4458 or www.chapinmfg.com

Felicitaciones!

Usted acaba de adquirir un producto de calidad Chapin.

Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas?

No regrese a la tienda;

llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!

Vous avez acheté un produit de qualité Chapin.

Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:

www.chapinmfg.com
Questions ?

Ne retournez pas au magasin.

Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com

6-5373

Holster

Funda

Étui

6-6092

Hose Black

Manguera para trabajos

pesados Negro

Tuyau pour service

intense Noir

6-7703

Extension wand,

Vara de extensión, Rallonge (1949)

6-6062

Shut-off Handle

Mango de cierre

Poignée du robinet

Attach nozzle to shut-off handle or extension wand.

TO LOCK HANDLE:

Push handle down to

depress coil spring and turn handle 1/4 turn clock-

wise, then allow handle to raise into lock position.

5. Pressurizing and Spraying

TO RELEASE HANDLE: Push down to depress coil spring and turn

handle counterclockwise 1/4 turn, then lift handle.

Pump until you feel resistance.

TO LOCK PUMP: Place pump prongs

down into slots in funnel, turn clamp

clockwise to furthest position under

bottom slot, then turn handle clockwise

until tightly locked and sealed in place.

TO UNLOCK PUMP: Turn handle counterclockwise until 3-prong clamp

is loose. Then rotate clamp counterclockwise to stop and lift out.

5. Pressurizing and Spraying, continued

SET COMPRESSOR REGULATOR AT 50 PSI

7. To Use Special Valve to Pressurize Sprayer

To pressurize sprayer by using the special valve first remove plastic

cap from the tire valve stem. Pressurize the sprayer by using a

standard air chuck connected to an air compressor as you would

inflating a tire on a car. After pressurizing the sprayer replace

plastic cap on the tire valve to avoid getting dirt in the valve.

For constant spraying, push down on shut-off handle

and move locking mechanism away from you. To re-

lease, squeeze handle and move the locking mechanism

back towards you.

6. Fatigue-Free Spraying