Chapin 1480 User Manual

Warning, Hose to tank 2. nozzle, Pre-use check 4. filling

Hazard: Improper use or failure to follow instructions can result in explosive failure causing

serious eye or other injury.

For safe use of this product you must read and follow all instructions.

Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up. Do not store or

ave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot

protection when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never

stand with face or body over

top of tank when pumping or loosening pump to prevent ejecting pump

assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means

other than the original pump. Do not attempt to modify or repair this product except with original

manufacturer’s parts. Never spray flammable materials or heat, pressure, or gas producing chemi-

cals. Always read and follow manufacturer’s instructions before use with this sprayer as some

chemicals may be hazardous when used with this sprayer.

WARNING!

Sk-1113-1

Note:

Your particular sprayer may not include all parts pictured above.

Nota:

Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.

Remarque :

Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.

Repair Parts Kit Gaskets and Seals (not included),

Juego de piezas de reparación, empaquetaduras y juntas (no incluido)

Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-1925

Printed in USA

1. Hose to Tank

2. Nozzle

Make sure hose is pushed all the

way to the tank. Make sure hose

clamp is tight and below the

hose barb. Turn clockwise with a

screwdriver to tighten.

1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.

2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,

replace hose before using. Replace with original manufacturer’s parts only.

3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of

tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank

weakening and could result in explosive bursting under pressure. If any of these signs are found, discard

tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.

4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.

5) Do: Pump plunger 10-20 strokes and inspect for leaks.

6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.

7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed

with Filling, Pressurizing and Spraying Instructions.

3. Pre-Use Check

4. Filling

1) Do: Turn pump handle counterclockwise and remove pump

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.

4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and

tighten securely.

5. Pressurizing and Spraying

WARNING:

Handling the brass parts of this product will expose you

to lead, a chemical known to the State of California to cause birth

defects and other reproductive harm. Wash hands after handling.

2-1100-23 (A) R0209

8. Care, Storage and Maintenance

1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and

Spraying Instructions, except pump unit only 8-10 strokes.

2) Do: Open shut-off and allow water to run through discharge assembly.

3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.

4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.

5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in

cover.

7. To Release Pressure

1) Do: With pump facing away, turn locked handle counterclockwise until air begins to escape.

Stop turning handle when you hear air escaping.

2) Do: Stay away from the sprayer until all air has escaped.

Hose Barb

Pump until you

feel resistance.

Turn handle clock-

wise to tighten.Push

handle down, turn

1/4 turn counter-

clockwise to release.

Push handle, down, turn 1/4

turn clockwise to lock. Begin

spraying.Re-pump sprayer as

required to maintain spray

force.

Attach nozzle to shut-off handle or extension wand.

Parts, Piezas, Pièces

6-6136

Hose

Manguera

Tuyau

6-1866

Shut-off Handle

Mango de cierre

Poignée du robinet

6-6000

Nozzle

Tobera

Buse

6-3337

Strap

Correa

Sangle

6-7711

Extension wand,

Vara de extensión, Rallonge

3-4843

Fan Nozzle Pack

Paquete de boquilla a chorro

Ensamble de buse à jet éventail

Red,

Fine spray for

finer washes

Blue,

Medium

spray for

sealers

Yellow,

Course spray

for semi- trans-

parent stains

For constant spraying, push down on shut-off handle

and move locking mechanism away from you. To re-

lease, squeeze handle and move the locking mechanism

back towards you.

6. Fatigue-Free Spraying

Fan spray

Stream spray

Congratulations!

You have just purchased a quality Chapin product.

Do Not Return To Store.

Call us @ 1-800-950-4458 or www.chapinmfg.com

Felicitaciones!

Usted acaba de adquirir un producto de calidad Chapin.

Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas?

No regrese a la tienda;

llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!

Vous avez acheté un produit de qualité Chapin.

Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:

www.chapinmfg.com
Questions ?

Ne retournez pas au magasin.

Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com

Insert Filter.

Insert O-ring.

Insert appropriate nozzle

into cap.

Attach cap with nozzle to end

of housing.

Cap

Nozzle

Filter

Housing

O-ring

Shut-off

or Wand