Actron Global OBD II Scan Tool 9620 - Manual (Page 9)

9620 Professional OBD II Scan Tool 9
1.4.3 Displaying Tool Information
From Tool Setup menu, select Tool Information and press ENTER. Use UP/DOWN
arrow keys to view information. Record information in case the need to contact customer
service arises.
1.4.4 Program Mode
Used to update scan tool’s software. Instructions will be provided with updates.
1.5 Personal Computer (PC) and Printer Interface
Scan tool is equipped with a standard 9 pin serial interface. Use connection to attach
tool to a PC or compatible printer.
• Personal Computer –
Use serial adapter to connect to a PC when updating to current available software.
Software updates may be purchased from Actron by calling the toll free number
provided or from the Actron website: www.actron.com.
Refer to Section 2.4.13 Print Data for default serial port settings and to make
changes to settings.
• Printer Connection –
Connect a compatible printer cable to the scan tool and Printer using specifications
below:
- If the printer connector is a 25 pin connector or if the gender is not compatible, an
adapter will be required.
- Adapters are available at most local PC stores or electronics outlets.
- A NULL modem adapter is required to be connected in series with scan tool and
printer cable.
1.6 Replacing the Battery
To replace the 9V battery, do the following:
• Remove screw from back of scan tool case.
• Slide battery cover back to disengage hooks.
• Replace 9V battery and place in compartment.
• Slide battery cover up, making sure hooks engage scan tool case.
• Install screw.
1.7 AC Adapter
The AC power adapter powers the tool when you review codes and print off-vehicle and when
you update the software vial a personal computer. The Scan tool is equipped to accept any
110 Vac–12 Vdc AC adapter with the following specifications.
• 300 mA minimum unregulated wall power adapter.
• Dimensions - 5.5 mm Outside Diameter, 2.5 mm Inside Diameter.
Setup Tool For
1) English/Metric
2)Display Contrast
`3)Tool Information
Tool Information:
`Serial No: 1360447]
SW ID: 86E3H[
HW Ver: 1
POS NEG
28 9620 Professional OBD II Scan Tool
Appendix A: Global OBD II PID List &
Definitions
All parameter identification data (PID) listed was verified on actual vehicles to guarantee
accuracy. Definitions used to describe all PIDs were obtained from reliable sources and
are accurate at time of printing. It is possible that some newer vehicles may contain different
data different from that listed. In these cases, refer to an applicable vehicle service manual.
Data Parameter List Format
The PID list is organized in alphabetical order — the same way the scan tool does. For each
PID, the type of reading are provided. Remember to always refer to a vehicle service manual
for detailed diagnostic procedures for troubleshooting incorrect PID readings.
Types of Data Parameters
INPUT: These data parameters are obtained from sensor outputs. Sensor outputs
are inputs to vehicle’s computer module(s). For example, if an Oxygen Sen-
sor was generating a 400mV signal, then the scan tool displays O2S (v) 0.40.
OUTPUT: These data parameters are outputs or commands that come directly from
computer module(s). For example; the ignition spark advance is controlled
by PCM, on most vehicles, monitoring this PID shows spark output from
PCM. The scan tool would display IGN ADV(°) 10.
CALCULATED: These data parameters are calculated after analyzing various inputs to the
vehicle’s computer module(s). For example, the engine load. The PCM
calculates this from sensor inputs and displays it in a percentage.
PCM VALUE: Is information that is stored in the computer module(s) memory and deter-
mined to be useful to service technician. An example of this is TROUBLE
CODE value, the DTC that caused a freeze frame capture.
NOTE: Several different causes can have the same parameter indication. For information on
diagnostics consult vehicle service manuals.
DATA PARAMETER LIST
ABS FRP (0 - 655350kPA) or (0 - 95050.5PSI)
Absolute Fuel Rail Pressure is the fuel pressure at the engine when reading in refer-
ence to atmospheric pressure.
ABS LOAD (0 - 100%)
Absolute Load Value is the normal value of air mass per intake stroke displayed as a
percent.
ABSLT TPS (0 - 100%)
Absolute Throttle Position represents normal distance throttle is opened.
ACC POS D,E or F (0 - 100%)
Accelerator Pedal Position represents normal distance gas pedal is pressed.
BARO PRESS (0 - 255kPA) or (0 - 36.9PSI)
Barometric Pressure is normally received from a dedicated barometer, manifold abso-
lute pressure sensor and other inputs during certain modes of driving.
NOTE: The Baro Press may not be the same as some weather services Barometric
Pressure due to being read at sea level.
CALC LOAD (0 - 100%)
Calulated LOAD Value indicates load on engine.
CAT TEMPxy (-40°C - 6513.5°C) or (-40 - 9999.9F)
Catalyst Temperature Bank shall display catalyst substrate temperature for bank cata-
lyst, if used by control module strategy for on board diagnostics monitoring, bank,
sensor catalyst or temperature sensor.