Datamax-O'Neil H-Class Internal Rewind Option User Manual
Page 6
4
4) Insert
the
creased edge of the Media
into a Slot, and then proceed according
to the width:
Rewinder
Hub
Media
Slot
creased edge
Full Width Media –
Insert the Retainer (Item
) into the
Slot, over the creased edge and
around the Rewinder Hub. Begin
printing.
Rewinder
Hub
Retainer
Slot
creased edge
Narrow Width Media –
While holding the creased edge in
place, manually rotate the Rewinder
Hub counterclockwise several times
to secure the Media. Then align the
Tabs to the Slots and slide the
Guide (Item
) onto the Rewinder
Hub. Position the Guide lightly
against the Media and tighten the
Thumbscrew. Begin printing.
Rewinder
Hub
Slots
Guide
Tabs
Thumbscrew
Media
5) When it’s time to unload the Internal
Rewind option, tear or cut the Media
(and, if installed, remove the Guide) then
grasp and slide the Roll off the
Rewinder Hub.
Rewinder
Hub
Guide
Thumbscrew
Media
Roll
- MF8I 270 User Guide (20 pages)
- MF8I Installation Guide (18 pages)
- MF8I Truck Mount Cable (2 pages)
- MF8I Locking Mounting Bracket (2 pages)
- MF8I Economy Mounting Bracket (2 pages)
- MF8I AN-15 (Line Printer and Easy Print Modes) (7 pages)
- MF8I AN-16 (Single Byte Character Set Font File Format) (8 pages)
- MF8I Quick Reference Programming Guide (72 pages)
- MF8I Configuration Program Installation (1 page)
- MF8I Bluetooth Management Component for Wavelink Avalanche (10 pages)
- A-Class Mark II Operator’s Manual (160 pages)
- A-Class Mark II Installation (2 pages)
- A-Class Mark II DMXrfNetIII (16 pages)
- A-Class Mark II DMXrfNetII (16 pages)
- A-Class Mark II RFID Quick Start Guide (6 pages)
- A-Class Mark II Programmer’s Manual (334 pages)
- ANDES 3 User Guide (32 pages)
- ANDES 3 Quick Start Guide (2 pages)
- ANDES Series Programmer’s Manual (67 pages)
- APEX 2 User Guide (28 pages)
- APEX 2 Quick Start Guide (2 pages)
- APEX 3 User Guide (27 pages)
- APEX 3 Quick Start Guide (2 pages)
- APEX 4 User Guide (30 pages)
- APEX 4 Quick Start Guide (2 pages)
- E-Class Mark III Operator’s Manual (90 pages)
- E-Class Mark III 4xxxxxxx Operator’s Manual (58 pages)
- E-Class Mark III 3xxxxxxx Operator’s Manual (58 pages)
- E-Class Mark III Paper Menu (7 pages)
- E-Class Mark III DPL Programmer’s Manual (296 pages)
- E-Class Mark III Printhead Bracket and Screw Upgrade (11 pages)
- H-Class Operator’s Manual (180 pages)
- Static brush (2 pages)
- H-Class Media Retainer (1 page)
- H-Class Thermal Transfer Option (12 pages)
- H-Class RFID Option (8 pages)
- H-Class Powered Internal Rewind Option (10 pages)
- H-Class Present Sensor Option (8 pages)
- H-Class Peel & Present Option (8 pages)
- H-Class Linear Scanner Option (26 pages)
- H-Class HD Peel & Present Option (10 pages)
- H-Class HD Cutter Option (12 pages)
- H-Class GPIO Option (14 pages)
- H-Class Cutter Option (10 pages)