Atec Tektronix-TG2000 - Manual (Page 4)

Data Sheet
HDST1 HD-SDI Stress Test Module
Input
Connector – 75 Ω BNC Connector.
Input Signal – HD-SDI signal.
Bit Rate – 1.485 Gb/s, 1.485/1,001 Gb/s.
Amplitude – 800 mV
p-p
±10%.
Standards Conformance – SMPTE 292M.
Return Loss – ≤15 dB to 742.5 MHz, ≤10 dB to 1.485 GHz.
Stress Output
Connector – 75 Ω BNC Connector.
Output Signal – HD-SDI signal.
Amplitude – 80 to 1040 mV
p-p
±5% (measured at 4.64 MHz square wave).
Amplitude Setting – 1% step.
Duty Cycle – 40% to 60%.
Rise/Fall Time – ≤270 ps (20% to 80%).
Return Loss – ≤15 dB to 1.485 GHz.
Jitter
HF Jitter
Jitter Waveform –
Sine wave.
Frequency – 0.1 Hz to 10 MHz.
Amplitude – 0.01 to 1 UI.
Amplitude Setting – 0.01 UI.
Amplitude Error –
≤0.1 UI (≤ 1 MHz, at 1 UI setting).
≤0.1 UI ±5% (≤5 MHz, at 1 UI setting).
≤0.1 UI ±10% (≤10 MHz, at 1 UI setting).
LF Jitter
Jitter Waveform –
Sine wave.
Frequency – 0.1 Hz to 10 kHz.
Amplitude – 0.01 to 20 UI.
Amplitude Setting – 0.01 UI.
Amplitude Error –
≤0.1 UI ±1% (≤1 kHz, at 8 UI setting).
≤0.1 UI ±5% (≤5 kHz, at 8 UI setting).
≤0.1 UI ±10% (≤10 kHz, at 8 UI setting).
Error Insertion
Error Rate – 0 to 120 errors/second.
Error Rate Setting – 0.1 errors/second.
Cable Simulator
Connector – 75 Ω BNC Connector.
Cable Type – L-5CFB.
Return Loss – ≤15 dB to 1.485 GHz.
Length – 20 m, 100 m.
AGL1 Analog Genlock Module
Inputs – Two 75 Ω loopthrough; one 75 Ω terminating.
Loopthrough Inputs –
Input range: ±6 dB from nominal black burst.
Return loss: ≥40 dB to 5 MHz.
Burst lock stability:
Amplitude changes: ≤1 ns change over a ±3 dB input level.
Jitter: ≤1 ns with ≥50 dB S/N ratio on a nominal amplitude reference input.
Typically ≤1°.
CW Input –
Input range: 1 to 2.25 V
p-p
.
Frequencies: NTSC and PAL F
sc
; 1, 5, and 10 MHz.
Return loss: ≥30 dB to 10 MHz.
Lock stability:
Amplitude changes: ≤1 ns over the valid input range.
Jitter: ≤1 ns with ≥50 dB S/N ratio for a 2 V reference input. Typically ≤0.5°.
Timing Adjustment (Black burst reference) –
Range: Anywhere within the color frame.
Resolution: ≤0.5°.
Color Framing – Correct for up to ±45° SCH error on the reference input.
Power Source
Mains Range –
Voltage: 87 to 132 or 174 to 250 VAC.
Frequency: 50 to 60 Hz.
Power Consumption – Typically 220 W for a fully loaded TG2000 mainframe.
Environmental
Temperature –
Operating: 0 °C to +40 °C.
Nonoperating: -40 °C to +65 °C.
Certifications
EMC – Certified to the EMC Directive 89/336/EEC.
Safety –
Approved to: CSA1010.1, ANSI S82.01.
Complies with: EN61010-1, IEC1010-1.
Physical Characteristics
Dimensions mm in.
Height 133 5.23
Width 483 19.0
Depth 584 23.0
Weight kg lb.
Net 17.3 38.0
Shipping 23.7 52.0
4 www.tektronix.com