Atec Yokogawa-WT500 - Manual (Page 3)

WT500 SPECIFICATION
Harmonic Measurement Function (/G5 Optional)
• During Harmonic Display
10 Hz ≤f<45 Hz
45 Hz ≤f≤440 Hz
440 Hz ≤1 kHz
1 kHz ≤2.5 kHz
0.4% of reading + 0.35% of range
0.75% of reading + 0.35% of range
1.2% of reading + 0.35% of range
5% of reading + 0.35% of range
0.85% of reading + 0.5% of range
1.5% of reading + 0.5% of range
2.4% of reading + 0.5% of range
10% of reading +0.5% of range
• When Line Filter is ON (5.5 kHz)
10 Hz ≤f<45 Hz
45 Hz ≤f≤440 Hz
440 Hz ≤1 kHz
1 kHz ≤2.5 kHz
2.5 kHz ≤5 kHz
0.15% of reading
+ 0.35% of range
0.15% of reading
+ 0.35% of range
0.2% of reading
+ 0.35% of range
0.8% of reading
+ 0.35% of range
3% of reading
+ 0.35% of range
0.15% of reading
+ 0.35% of range
0.15% of reading
+ 0.35% of range
0.2% of reading
+ 0.35% of range
0.9% of reading
+ 0.35% of range
3% of reading
+ 0.35% of range
0.35% of reading
+ 0.5% of range
0.25% of reading
+ 0.5% of range
0.4% of reading
+ 0.5% of range
1.7% of reading
+ 0.5% of range
6% of reading
+ 0.5% of range
• When Line Filter is OFF
Fundamental Frequency
10 Hz to 75 Hz
75 Hz to 150 Hz
150 Hz to 300 Hz
300 Hz to 600 Hz
600 Hz to 1200 Hz
Sample Rate
f*1024
f*512
f*256
f*128
f*64
Window Width
1
2
4
8
16
Upper Limit of Analyzed orders
50
32
16
8
4
Sampling Frequency Voltage Current Power
Sampling Frequency Voltage Current Power
However, all the items below apply to all tables.
• When the crest factor is set to 3
• When
λ (power factor) = 1
• Power figures that exceed 440 Hz are reference values.
• For nth order component input, add {n/(m+1)}/50% of (the nth order reading) to the n + mth order and n-mth
order of the voltage and current.
For the n+mth order and n-mth order of power, add {n/(m+1)/25} of the nth order reading.
• Add (n/500)% of reading to the nth component of the voltage and current, and add (n/250)% of reading to the
nth component of the power.
• Accuracy when the crest factor is 6: The same as when the range is doubled for crest factor 3.
• The accuracy guaranteed range by frequency and voltage/current is the same as the guaranteed range of
normal measurement. If the amplitude of the high frequency component is large, influence of approximately
1% may appear in certain orders. The influence depends on the size of the frequency component. Therefore, if
the frequency component is small with respect to the range rating, this does not cause a problem.
Delta Calculation Function (/DT Optional)
FQ) is installed, the frequencies of the voltages and currents
being input to all input elements can be measured.
Reciprocal method
Data Update Rate
Measuring Range
100 ms 25 Hz ՅfՅ100 kHz
200 ms 12.5 Hz ՅfՅ100 kHz
500 ms 5 Hz ՅfՅ100 kHz
1 s 2.5 Hz ՅfՅ100 kHz
2 s 1.5 Hz ՅfՅ50 kHz
5 s 0.5 Hz ՅfՅ20 kHz
±0.06% of reading
When the input signal levels are greater than or equal to 25
mV (current external sensor input) and the signal is greater
than or equal to 30% (0.1 Hz–440 Hz, frequency filter ON), of
the measurement range.
However, when the measuring frequency is smaller or equal
to 2 times of above lower frequency, the input signal is
greater than or equal to 50%.
Add 0.05% of reading when current external input is smaller
than or equal to 50 mV input signal level for each is double for
crest factor 6.
99999
0.0001 Hz
Select ON/OFF
RGB Video Signal (VGA) Output Section (/V1 Optional)
15-pin D-Sub (receptacle)
VGA compatible
Ethernet Communications (/C7 Optional)
1
RJ-45 connector
Conforms to IEEE 802.3.
Ethernet 100BASE–TX
Max.100 Mbps
TCP/IP
FTP server, DHCP, DNS, Remote control (VXI-11)
USB port (PC)
Type B connector (receptacle)
Max.12 Mbps
1
Remote control (USB-TMC)
Models with standard USB ports that run Windows 2000,
Windows XP, or Windows Vista with USB port
as a standard.
Self Power
USB port (Peripheral)
Type A connector (receptacle)
Conforms to USB Rev.2.0
Max. 480 Mbps
2
104 keyboard (US) and 109 keyboard (Japanese) conforming
to USB HID Class Ver.1.1devices
USB (USB Mass Storage Class) flash memory
5 V, 500 mA (per port)
However, device whose maximum current consumption
exceeds 100 mA cannot be connected simultaneously to the
two ports.
Master/Slave Synchronization Signal Input/External Clock Input (Select)
BNC connector: Both slave and master
BNC connector
TTL
Same as the measurement range for frequency
50% duty ratio square wave
10 Hz to 1.2 kHz
50% duty ratio square wave
1 µs
Within (1 µs + 1 sample rate)
GP-IB Interface (/C1 optional)
Use one of the following by NATIONAL INSTRUMENTS:
• AT-GPIB
• PCI-GPIB, PCI-GPIB+, and PCIe-GPIB
• PCMCIA-GPIB and PCMCIA-GPIB+
Use driver NI-488.2M version 1.60 or later.
IEEE St'd 488-1978 (JIS C 1901-1987).
SH1, AH1, T6, L4, SR1, RL1, PP0, DC1, DT1, and C0.
IEEE St'd 488.2-1992.
ISO (ASCII)
Addressable mode
0–30
Remote mode can be cleared using the LOCAL key (except
during Local Lockout).
General Specifications
Approximately thirty minutes.
5–40
°C
20–80% (when printer not used)
(No condensation may be present)
2000 m or less
Inside of room
-25–60
°C (no condensation may be present)
20 to 80% RH (no condensation)
100–240 VAC
90–264 VAC
50/60 Hz
48 to 63 Hz
80 VA (when using built-in printer)
Approximately 6.5 kg (including main unit, 3 input elements,
and options)
All Installed Elements
PLL synchronization
PLL source of the fundamental frequency is in the range 10
Hz–1.2 kHz.
Select voltage, current, or external clock for each input
element.
32 bits
Rectangular
Set using a line filter (5.5 kHz or OFF)
Item
Voltage
Current
Delta Calculation Setting
difference
3P3W→3V3A
DELTA→STAR
STAR→DELTA
difference
3P3W→3V3A
DELTA→STAR
STAR→DELTA
Symbols and Meanings
̅U1: Differential voltage determined by computed u1 and u2
̅U1: Line voltage determined in the calculation for a 3 phase 3 wire connection
̅U1, ̅U2, ̅U3: Phase voltage determined in the calculation for 3 phase
3 wire (3V3A) connection
̅U1, ̅U2, ̅U3: Line voltage determined in the calculation for a 3 phase 4
wire connection
̅11: Differential current determined by computation
Phase current that are not measured can be computed
Neutral line current
Neutral line current
Sample rate (sampling frequency), window width, and upper limit of analyzed orders for PLL
synchronization.
Accuracy ±(reading error + measurement range error) (for crest factor 3)
Measurement method
Measurement range
Accuracy
Max. display resolution
Min. frequency resolution
Frequency Filter
Connector type
Output format
Number of communication ports
Connector type
Electrical and mechanical specifications
Transmission system
Transmission rate
Protocol
Supported Services
Connector
Electrical and Mechanical Specifications Conforms to USB Rev.1.1
Speed
Number of Ports
Supported service
Supported Systems
Power Supply
Connector
Electrical and Mechanical Specifications
Speed
Number of Ports
Supported keyboards
Supported USB memory devices
Power supply
Master/Slave Synchronization Signals
Connector type
External Clock Input
Connector type
Input level
Inputting the synchronization source as the Ext Clk of normal measurement.
Frequency range
Input waveform
Inputting the PLL source as the Ext Clk of harmonic measurement. (/G5 option is required)
Frequency range
Input waveform
For Triggers
Minimum pulse width
Trigger delay time
Card driver
Conforms electrically and mechanically
Functional specification
Conforms to protocol
Encoding
Mode
Address
Clear remote mode
Warm-up time
Operating temperature:
Operating humidity:
Operating altitude
Operating area
Storage environment:
Storage humidity:
Rated supply voltage
Allowed supply voltage fluctuation range
Rated supply frequency
Allowed supply frequency fluctuation
Maximum power consumption
Weight
Measure source
Method
Frequency range
PLL source
Data length for FFT
Window function
Anti-aliasing filter