Atec Spirent-N4U - Manual (Page 2)

© 2013 Spirent Communications, Inc. All of the company names and/or brand names and/or product names referred to in this document,
in particular the name “Spirent” and its logo device, are either registered trademarks or trademarks pending registration in accordance
with relevant national laws. All rights reserved. Specifications subject to change without notice. Rev. A 10/13
AMERICAS 1-800-SPIRENT • +1-818-676-2683 • [email protected]
EUROPE AND THE MIDDLE EAST +44 (0) 1293 767979 • [email protected]
ASIA AND THE PACIFIC +86-10-8518-2539 • [email protected]
SPT-N4U COMPACT CHASSIS
SPIRENT
SPECIFICATIONS
Chassis design and form factor • EIA 19” rack compatible, 4RU high
• 2 test module slots
• Side-to-side airflow (left to right)
• Field replaceable system hard drive
Administration and Operation • Up to 32 simultaneous users per chassis
• IPv4 and IPv6 admin network compatible
• Built-in Android touchscreen
• SSH terminal emulation via Ethernet
• Direct via external video connector and
USB ports
Timing Synchronization • Via external timing receiver: PTP (IEEE 1588v2 Precision Timing Protocol), GPS (Global Positioning System),
CDMA (Code Division Multiple Access), TIA/EIA–95B and NTP (Network Timing Protocol)
• Direct chassis clustering and automatic sync cable calibration
Indicators and Controls • System power on/off
• Controller reset
• Built-in LCD touchscreen
• Front panel LEDs: Temperature, fan, admin link, system and system power status; test module slot power
status; chassis synchronization master/slave and status; and admin Ethernet link, speed and activity
Physical • Dimensions: 17.5”W x 7”H x 27.0”D (44.45 cm x 17.8 cm x 68.6 cm) 25” (63.5 cm) depth measured from
front mounting flange
• Installation and shipping weight: 58.6 lbs. (26.6 kg) (no test modules installed)
• Approximate weight fully loaded: 81.6 lbs. (37 kg)
Power • Inlet AC for STC-N4U-110: 2 x 115V @ 12 A, or 2 x 230V @ 6A; one circuit dedicated for system and slot 1
operation, and one circuit for slot 2
• Inlet AC for STC-N4U-220: 1 x 230V @ 12A
• Peak power requirement: 2kW for fully loaded chassis
Environmental • Operating requirements: 59° to 95° F (15° to 35° C); 20% to 80% relative humidity
• Heat dissipation: 6000 BTUs/h (assumes 80% heat load for air conditioning)
Connectors • Front panel: 4 x USB 2.0 (keyboard or mouse), DVI-I / VGA D15 video (console), 1 PPS and 10, MHz BNCs and
DB9 serial DCE (for ETR support), 10/100/1000M BASE-T RJ-45 Ethernet (admin), Synch in/out RJ-45 (chassis
synch chain), 1588 (unused) and System hard drive access panel
• Rear panel: C20 power connector(s)
ORDERING INFORMATION
Description
Spirent Chassis Part Number
SPIRENT N4U CHASSIS AND CONTROLLER WITH 110V
AC POWER SUPPLIES
SPT-N4U-110
SPIRENT N4U CHASSIS AND CONTROLLER WITH 220V
AC POWER SUPPLIES
SPT-N4U-220
Accessories
HYPERMETRICS SINGLE-SLOT CARD CARRIER FOR N11U/
N4U CHASSIS
ACC-2017A
HYPERMETRICS DUAL-SLOT CARD CARRIER FOR
N11U/N4U CHASSIS
ACC-2018A
HARD CASE FOR SPT-N4U ACC-2019A
C20 TO C19 PWR CORD, CHS-N11U OR CHS-11U TO
PDU, 20A 250V
ACC-2020A
REQUIREMENTS
• Windows-based workstation with 10/100/1000 Mbps
Ethernet NIC; mouse and color monitor required for
GUI operation
•
Linux or Windows-based workstation for Tcl and other
API automation
SPIRENT SERVICES
Spirent Global Services provides a variety of professional
services, support services and education services—all focused
on helping customers meet their complex testing and service
assurance requirements. For more information, visit the Global
Services website at
www.spirent.com or contact your Spirent
sales representative.