Atec Narda-EA5091-EB5091-EC5091-ED5091 - Manual (Page 3)

NSTS 0807-E0239A-0.0 3 / 3 Subject to change
Narda Safety Test Solutions GmbH
Sandwiesenstrasse 7
72793 Pfullingen, Germany
Phone: +49 (0) 7121-97 32-777
Fax: +49 (0) 7121-97 32-790
E-Mail: [email protected]
www.narda-sts.de
Narda Safety Test Solutions
435 Moreland Road
Hauppauge, NY 11788, USA
Phone: +1 631 231-1700
Fax: +1 631 231-1711
E-Mail: [email protected]
www.narda-sts.com
Narda Safety Test Solutions Srl
Via Leonardo da Vinci, 21/23
20090 Segrate (Milano), Italy
Phone: +39 02 2699871
Fax: +39 02 26998700
E-Mail: [email protected]
www.narda-sts.it
SPECIFICATIONS a
Probe EA … ED5091 Electric (E-)Field
Frequency range (b) 300 kHz to 50 GHz (EA5091, EC5091, ED5091) 3 MHz to 50 GHz (EB5091)
Type of frequency response Shaped, see table on page 2
Measurement range 0.5 to 600 % of Standard (Power Density)
Dynamic range 30 dB
CW damage level 2000 % of Standard 700 mW/cm²
Peak damage level (c) 32 dB above Standard
Sensor type Combined diodes/ thermocouples
Directivity Isotropic (Tri-axial)
Readout mode / spatial assessment Combined 3-axis (RSS)
UNCERTAINTY
Flatness of frequency response
(d)
Calibration uncertainty not included
±2 dB from Standard
Calibration uncertainty (e)
±1.5 dB (< 1.8 GHz)
±0.7 dB (1.8 GHz to 40 GHz)
±1 dB (@ 45.5 GHz)
Linearity
Referred to 100 %
±3 dB (< 4 % of Standard)
±1 dB (4% to 12 % of Standard)
±0.5 dB (12 % to 600 % of Standard)
Isotropic response (f) typ. ±1 dB (≥ 10 MHz)
GENERAL SPECIFICATIONS
Calibration frequencies
0.3/ 3/ 10/ 30/ 100/ 300/ 750 MHz 1/ 1.8/ 2.45/ 4/ 8.2/ 10/ 18/ 26.5/ 40/ 45.5 GHz
Recommended calibration interval 12 months
Temperature range
Operating
Non-operating (transport)
0 °C to +50 °C
-40 °C to +70 °C
Humidity 5 to 95 % RH @ ≤25 °C ≤23 g/m³ absolute humidity
Size 350 mm x 104 mm Ø
Weight 240 g
Compatibility NBM-500 series meters
(a)
Unless otherwise noted specifications apply at reference condition: device in far-field of source, ambient temperature 23±3 °C, relative air humidity 40% to 60%, sinusoidal signal
(b) Cutoff frequency at approx. -3 dB
(c) Pulse length 1µsec, duty cycle 1:1000
(d) Frequency response can be compensated for by the use of correction factors stored in the probe memory
(e) Accuracy of the fields generated to calibrate the probes
(f) Uncertainty due to varying polarization (verified by type approval test for meter with probe). Ellipse ratio included and calibrated for each probe
ORDERING INFORMATION
Part number P/N
Probe EA5091, Shaped E-field, FCC for NBM, 300 kHz - 50 GHz, isotropic 2402/07
Probe EB5091, Shaped E-field, IEEE for NBM, 3 MHz - 50 GHz, isotropic 2402/08
Probe EC5091, Shaped E-field, SC6 Canada for NBM, 300 kHz - 50 GHz, isotropic 2402/09
Probe ED5091, Shaped E-field, ICNIRP for NBM, 300 kHz - 50 GHz, isotropic 2402/10