Atec Agilent-33250A - Manual (Page 3)

System Characteristics
Configuration Times (typical) 9
Function change
Standard
100 ms
Pulse 660 ms
Built-in arb 220 ms
Frequency change 20 ms
Amplitude change 50 ms
Offset change 50 ms
Select user arb < 900 ms for < 16K pts.
Modulation change < 200 ms
Arb Download Times GPIB/RS-232 (115Kbps)
Arb Length Binary ASCII Integer ASCII Real
64K points 48 sec 112 sec
186 sec
16K points 12 sec 28 sec 44 sec
8K points 6 sec 14 sec 22 sec
4K points 3 sec 7 sec 11 sec
2K points 1.5 sec 3.5 sec 5.5 sec
Trigger Characteristics
Trigger input
Input level
TTL compatible
Slope rising or falling,
(selectable)
Pulse width > 100 ns
Input impedance 10 kΩ, DC coupled
Latency
Burst
< 100 ns (typical)
Sweep < 10 µs (typical)
Jitter (rms)
Burst
1 ns; except pulse,
300 ps
Sweep 2.5 µs
Trigger output
Level
TTL compatible into
50Ω
Pulse width > 450 ns
Maximum rate 1 MHz
Fanout ≤ 4 Agilent 33250A’s
(or equivalent)
Clock Reference
Phase Offset
Range
-360° to +360°
Resolution 0.001°
External Reference Input
Lock range
10 MHz ± 35 kHz
Level 100 mVpp to 5 Vpp
Impedance 1 kΩ nominal, ac
coupled
Lock time < 2 s
Internal Reference Output
Frequency 10
MHz
Level 632 mVpp (0 dbm),
nominal
Impedance 50Ω nominal, ac
coupled
Sync Output
Level TTL compatible
into > 1 kΩ
Impedance 50 Ω nominal
General
Power supply 100-240 V, 50-60 Hz
100-127 V, 50-400 Hz
Power consumption 140 VA
Operating temp.
0°C to 55°C
Storage temp. -30°C to 70°C
Stored states 4 named user configu-
rations
Power on state default or last
Interface IEEE-488 and
RS-232 std.
Language SCPI-1997, IEEE-488.2
Dimensions (WxHxD)
Bench top
254 x 104 x 374 mm
Rackmount 213 x 89 x 348 mm
Weight 4.6 kg
Safety designed to EN61010-1, CSA1010.1,
UL-311-1
EMC tested to IEC-61326-1
IEC-61000-4-3 criteria B
IEC-61000-4-6 criteria B
Vibration and shock MIL-T-28800E, Type III,
Class 5
Acoustic noise 40 dBA
Warm-up time 1 hour
Calibration interval 1 year
Warranty 1 year
3
1 Harmonic distortion at low amplitudes is limited by a -70 dBm floor
2 Harmonic distortion at 40 MHz only is -33 dBc
3 Spurious noise at low amplitudes is limited by a -75 dBm floor
4 Edge time decreased at higher frequency, 3.5 nS (typical)
5 20 mVpp to 20 Vpp into open-circuit load
6 dB rounded to 1 digit, instrument adheres to “%” specification
7 Short-circuit protected to ground at all times
8 Sine and square waveforms above 25 MHz only with infinite burst count
9 Time to change parameter and output new signal