beautypg.com

Extron Electronics PowerCage MTP R AV Setup Guide User Manual

Powercage, Mtp t av and mtp r av board setup guide, Installation

background image

PowerCage

MTP T AV and MTP R AV Board

Setup Guide

Continued on side 2.

1

The Extron

®

PowerCage MTP T AV and

MTP R AV are twisted pair transmitters and
receivers in a modular board format for the
PowerCage 1600 modular enclosure. They
transmit or receive composite video or
S-video and audio over CAT 5-type cable.
Both boards can be used with any CAT 5, 5e, or 6 cable, or Extron
Enhanced Skew-Free

A/V UTP cable for cable runs up to 1000 feet

(300 m). The boards mount in any of the 16 expansion slots at the rear of
the PowerCage 1600.
Refer to the PowerCage MTP T AV and MTP R AV User Guide and the
PowerCage 1600 Enclosure User Guide, available at

www.extron.com

.

NOTE:

The hot-swappable, modular design allows for replacing or
upgrading boards in the field at any time, without having to
power down the system.

Installation

1.

Select an open slot at the rear, or take out a blank plate by loosening the two
screws (top and bottom), and lifting the blank away.

NOTE:

If a board is already in the slot, loosen the screws and remove the board.

2.

Remove the new board from the box,
holding the board by the frame.

3.

Hold the board with the signal connectors
towards you and the MTP AV board name
and LED at the top, and align the top and
bottom grooves of the board with the slide
posts in the selected enclosure slot.

4.

Carefully slide the board into the slot,
aligning that the two tabs on the lower
front end of the board with the matching
ports in the enclosure. Push the board
firmly into place.

5.

Tighten the screws to secure the board.

6.

If applicable, repeat steps 1 through 5
for any other modular boards.

NOTE:

Cover all empty board slots; do not leave them open. Using a tool, securely
fasten the screws for boards and blank panels after initial installation and
subsequent removal and replacement of the boards.

MONO

A

UDIO OUTPUT

1

2

S

H

A

R

P

GAIN

Y/VI

D

C

INPU

T

Po

we

rCa

ge

MTP R

AV

Tx

R

x

HD/SDI INPU

T

H

D/SDI OUTPUTS

M

O

D

E

Po

we

rCa

ge

FO

X 3G HD-SD

I

1

2

REMO

TE

RS-232

RS-232

O

VER FIBER

Tx Rx

Tx

ALARM

Rx

OUTPUT

RG

B

Po

we

rCa

ge

FO

X 4G RX RG

B

Tx Rx

L

R

A

UDI

O

5A M

AX.

100-2

40V

50

/60H

z

N15

778

C

US

LIS

TED

1T2

3

I.T.

E.

Screws
(2 per board)

1

2

REM

O

T

E

RS-232

RS-232

O

VER FIBE

R

Tx Rx

Tx

ALAR

M

Rx

OUTPUT

RG

B

Po

we

rCa

ge

FO

X 4G RX RG

B

Tx Rx

L

R

A

UDI

O

Align board and
slide into slot.

16 Available Single Board Slots or
8 Double Board Slots

Power
Supply

MTP R AV

MON

O

AUDIO OUTPUT

1

2

SHAR

P

GAI

N

Y/VID

C

INPUT

PowerCage

MTP R AV

OUTPUT

PowerCage

MTP T AV

AUDIO INPU

T

L

R

Y/VI

D

C

MTP T AV

S-video

Composite

Video

Y

/VID

C

C

Y/

VID

OR

7.

If power has been removed, reconnect and power on the PowerCage. The LED on
the board lights green and the new board is auto-detected.

8.

Following the image at right, connect input or output
device cables to the the two BNC connectors for S-video
signals or for composite video signals.

This manual is related to the following products: