Extron Electronics MKP 10 MAAP - Manual

Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
www.extron.com
MKP 10 MAAP Installation and Operation
Selecting an input or output number by rotating the MKP 3000’s Select knob in a large
matrix switcher system can be inconvenient. The optional MKP 10 MAAP keypad
allows more rapid input and output selection.
MKP 10 MAAP Mounting
The MKP 3000 MAAP has a space that allows the
installation of an MKP 10 keypad.
Mount the MKP 10 MAAP to the MKP 3000 MAAP as
follows:
The proper MKP 10 orientation is with the power
LED up.
1. Sandwich the MKP 3000 MAAP panel between
the MKP 10 module (without its front panel) and
the MKP 10’s front panel. Secure the front
panel to the control panel module with the
included #4-40 screws.
2. See the drawing below. Connect the
serial control and power cable between
the J1 connector (
1 ) on the MKP 10
MAAP and the Remote Keypad port
(
2 ) on the rear of the MKP 3000 MAAP.
68-1070-01
Rev. A
05 05
PO WER RESET
I/O
SEL ECT
Ex tro n
MK P 30 00 MA AP
BA CK
CA NC EL
1
2 3
4 5 6
7 8
9
0
MKP 1 0
(4) #4-40
Screws
Extron
MKP 10
Module
Extron
MKP 3000 MAAP
Panel
Extron
MKP 10
Front Panel
2
1
3. Mount the MKP 3000 MAAP panel (with the mounted MKP 10 MAAP) to the wall
box or mounting bracket.
MKP 10 MAAP Operation
BACK CANCEL
1 2 3
4 5 6
7 8 9
0
MKP 10
2 4
1
3
BACK CANCEL
1 Power LED — When lit, this LED indicates that power is applied to the
MKP 10 MAAP.
The MKP 10 MAAP receives power from the connected
MKP 3000 MAAP.
2 Cancel key — Press and release the cancel key to reset the selected input or
output value shown in the MKP 3000’s LCD display to 000 before using the
numeric keys (
3 ) to enter a specific value.
3 Numeric keys — Press and release the numeric (0 — 9) keys to enter a
specific value as the selected input or output shown in the MKP 3000’s
LCD display.
4 Back key — Press and release the Back key to backspace (erase) the least-
significant (rightmost) digit shown in the LCD display.
Part Numbers
MKP 10 MAAP Remote Keypad Part number
MKP 10 MAAP, black 60-710-10
MKP 10 MAAP, white 60-710-20
MKP 10 MAAP, RAL 9010 (pure white) 60-710-50
MKP 3000 MAAP Part number
MKP 3000 MAAP, black 60-709-02
MKP 3000 MAAP, white 60-709-03
MKP 3000 MAAP, RAL 9010 (pure white) 60-709-05
Included parts
Included parts
MKP 10 MAAP
Serial and power cable
Installation hardware
Wall box Part number
Three-gang “J” box 2.5” deep 980083