Extron Electronics JMP 9600 Setup Guide - Manual

This guide provides quick start instructions for an experienced installer to set up and operate the Extron
®
JMP 9600 HD and JMP 9600 2K Media Players.
NOTE: For full installation, configuration, and operation details, see the
JMP 9600 Media Player User Guide, available at www.extron.com .
The JMP 9600 Media Player is a high quality video and audio playback device that provides one
or two video playback channels. Depending on the model, the player supports playback of video
at HD (720p and 1080i) or 2k (1080p) resolutions. Both video outputs support DVI-I (digital and analog RGB) and HD-SDI formats.
Connections
INPUT: 100-240VAC, 0.4-1A, 50/60HZ
USE ONLY: F2 AH 240V FUSES.
1-2 3-4 5-6 7-8
DIGITAL VIDEO OUTPUTS
DIGITAL
AUDIO
OUT
2 1
DVI-I-1 DVI-I-2
HDSDI
JMP 9600
9-10 11-12 13-14 15-16
1 LAN 2
REMOTE 1
GENLOCK
LOCK LTC
IN
OUT OUT
IN
REMOTE 2
NC C NC NC NO NC C C C NO NO NO
DIGITAL INPUTS RELAY OUTPUTS
1 2 3 4 + - + - + - + - 12V
POWER R1 R3 R4 R2
OUT
1a 4 1b 13
12 9 10 11
3 5 6 2b 2a
8 For Factory
Use Only 7
a
Digital Video Outputs, DVI-I connectors — Connect one or two DVI displays to the DVI-I-1 and DVI-I-2 connectors for the direct
digital image and RGB video output.
NOTE : Both DVI connectors can output single-link DVI (digital) video and traditional analog RGBHV video.
b
Digital Video Outputs, HD-SDI connectors — Connect one or two HD-SDI devices to the HDSDI-1 and HDSDI-2 BNC connectors.
NOTE : In single-channel mode with dual-link HD-SDI selected, both HD-SDI connectors are required for a single image.
c
Digital Audio Output connectors — Connect devices that can receive and decode AES3-encoded audio to these 8 BNC connectors
to receive up to 16 channels of audio.
NOTES : • The AES3 protocol supports two channels of linear PCM (wave) audio on one BNC connector.
• For compatibility with the 2-channel mode of the player, media files must be encoded with 4:2:2 subsampled
color video sampling and a maximum of eight channels of audio. With 4:2:2 video:
z
Audio channels 1 through 8 are associated with video channel 1.
z
Audio channels 9 through 16 are associated with video channel 2.
d
Genlock Input connector — Connect an external genlock signal to this BNC connector for genlocking the video signal in
broadcast or other sync-critical NTSC or PAL applications. Use a tee connector or distribution amplifier to connect any
downstream equipment that requires genlocking
e
Lock Input and Output connectors —
NOTES : • Use only one of the Genlock and Lock sync types (items d and e ) available).
• The Lock connectors support ESGEN and MSGEN, which are proprietary sync signals that are native to
Electrosonic ® products that have been acquired by Extron and to older Electrosonic products.
Lock Input connector — Connect an external ESGEN or MSGEN sync signal to this 6-pin mini-DIN connector for the media player
to function as a sync slave of another device.
Lock Output connector — Connect any downstream equipment that requires an ESGEN sync signal to this 6-pin mini-DIN
connector to either route the external sync signal throughout the system or for the media player to function as a sync master.
1
JMP 9600 • Setup Guide